Connecting a Component Video source device | BenQ MS521 specification

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output jacks available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device. Match the color of the plugs to the color of the jacks; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the COMPUTER IN-1or COMPUTER IN-2jack on the projector.

3.If you wish to make use of the projector speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Image 22

BenQ MS521 Connecting a Component Video source device, To connect the projector to a Component Video source device

Contents

User Man ual Table of contents Uninterruptible power supply Areas where the mains voltageYour projector through a power Refer servicing to qualified service personnel Safety Instructions Do not block the ventilation holes Safety Instructions Projector features Shipping contents Projector exterior view Rear/lower side Controls and functions Ceiling mounting the projector Remote control Source Volume +Setting Mute Replacing the remote control battery Front Table Choosing a locationFront Ceiling Obtaining a preferred projected image size Projection dimensionsMS521/MX522/MS511H MW523/TW523 762 646 404 Connection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computer Connecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source device Connecting a Component Video source device To connect the projector to a Component Video source device Connecting an S-Video/composite source device To connect the projector to an S-Video/Video source device Operation Starting up the projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test pattern Correcting keystone Using the menus Setting a password Using a security cable lockUtilizing the password function Securing the projector Entering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the image Using Wall Color Fine-tuning the image quality in user modes 3D Color Management Setting a preferred color temperatureAbout color temperatures Press MODE/ENTER and the 3D Color Management page displays Magenta Cyan Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right How to use the Timer On key? To cancel the timer, perform the following stepsRemote paging operations Hiding the image Freezing the image To activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environment Use Teaching Template Lamp Mode Description Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Personalizing the projector menu display Shutting down the projector Menu system Menu operationMain menu Sub-menu Options Picture System Setup Basic Setup Advanced Description of each menu Teaching Template Reference Picture ModePicture menu Mode Reset Picture Temperature ColorTemperature Fine Tuning 3D Color Setting Settings TimerInstallation Presentation Panel Key Basic menuOperation Lock Audio System Setup Advanced menuHigh Altitude Lamp Caption Reset AllClosed Standby System Information menuCurrent Status Care of the projector Cleaning the lensCleaning the projector case Storing the projector Lamp information Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Getting to know the lamp hourPage Timing of replacing the lamp Status Message Replacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Projector does not turn on Remote control does not workPassword is incorrect No picture Specifications Ceiling mount installation Dimensions301.6 219.2 111.3 Resolution Mode Vertical Horizontal Pixel Frequency KHz MHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video input Video timing Supported 3D signal for Hdmi Hdcp inputPC timing Supported 3D signal for D-SUB input SXGA85 Supported 3D signal for Video and S-Video input Copyright Limited warrantyPatents Disclaimer FCC statement for the United States only Warranty and Copyright information For UK only CE DOC KONFORMITÄTSERKLÄRUNG Konformitetsdeklaration Uyum Beyani Deklaracija O Usklaĉenosti Overensstemmelseserklæring Vaatimustenmukaisuusvakuutus Weee directive Directiva Weee Ⱦɢɪɟɤɬɢɜɚ Weee Dyrektywa Weee Directiva REE Weee direktiva ȄįȘȖȓĮ Weee For Korea WLAN/BT module Warranty and Copyright information Weee UAE Singapore