Connecting an S-Video/composite source device | BenQ MS521 specs

Connecting an S-Video/composite source device

Examine your Video source device to determine if it has an unused S-Video/composite output jack available:

•If it has both jacks, use the S-Video output jack for connection as the S-Video terminal provides better picture quality than the Video terminal.

•If it has either of the output jack, you can also continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video/Video source device:

1.Take an S-Video/Video cable and connect one end to the S-Video/Video output jack of the Video source device.

2.Connect the other end of the S-Video/Video cable to theS-Video/ Video jack on the projector.

3.If you wish to make use of the projector speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 23

Image 23

BenQ MS521 Connecting an S-Video/composite source device, To connect the projector to an S-Video/Video source device

Contents

User Man ual Table of contents Refer servicing to qualified service personnel Areas where the mains voltageYour projector through a power Uninterruptible power supply Safety Instructions Do not block the ventilation holes Safety Instructions Projector features Shipping contents Rear/lower side Projector exterior view Controls and functions Ceiling mounting the projector Remote control Mute Volume +Setting Source Replacing the remote control battery Front Ceiling Choosing a locationFront Table MS521/MX522/MS511H Projection dimensionsObtaining a preferred projected image size 762 646 404 MW523/TW523 Connection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitor Connecting Video source devices To connect the projector to a Hdmi source device Connecting a Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source device To connect the projector to an S-Video/Video source device Connecting an S-Video/composite source device Starting up the projector Operation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Use build-in test pattern Fine-tuning the image size and clarity Correcting keystone Using the menus Securing the projector Using a security cable lockUtilizing the password function Setting a password Changing the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Using Wall Color Press MODE/ENTER and the 3D Color Management page displays Setting a preferred color temperatureAbout color temperatures 3D Color Management Magenta Cyan Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Hiding the image Operating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude Mode Use Teaching Template Personalizing the projector menu display Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Lamp Mode Description Shutting down the projector Main menu Sub-menu Options Menu operationMenu system Picture System Setup Basic Advanced Setup Description of each menu Template Teaching Mode Picture ModePicture menu Reference Setting Temperature ColorTemperature Fine Tuning 3D Color Reset Picture Presentation TimerInstallation Settings Lock Basic menuOperation Panel Key Lamp System Setup Advanced menuHigh Altitude Audio Standby Reset AllClosed Caption Status Information menuCurrent System Storing the projector Cleaning the lensCleaning the projector case Care of the projector Getting to know the lamp hour Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lamp Replacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off No picture Remote control does not workPassword is incorrect Projector does not turn on Specifications 301.6 219.2 111.3 DimensionsCeiling mount installation Supported timing for PC input Timing chartResolution Mode Vertical Horizontal Pixel Frequency KHz MHz Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Video and S-Video input Supported timing for Component-YPbPr input PC timing Supported 3D signal for Hdmi Hdcp inputVideo timing SXGA85 Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Disclaimer Limited warrantyPatents Copyright FCC statement for the United States only Warranty and Copyright information For UK only CE DOC KONFORMITÄTSERKLÄRUNG Konformitetsdeklaration Uyum Beyani Deklaracija O Usklaĉenosti Overensstemmelseserklæring Vaatimustenmukaisuusvakuutus Weee directive Directiva Weee Ⱦɢɪɟɤɬɢɜɚ Weee Dyrektywa Weee Directiva REE Weee direktiva ȄįȘȖȓĮ Weee For Korea WLAN/BT module Warranty and Copyright information Weee UAE Singapore