Manuals / BenQ / Computer Equipment / Projector

BenQ MS524/MS514H/MX525/MW526/TW526 user manual Connecting video source devices, Connecting audio

Models: MS524/MS514H/MX525/MW526/TW526

1 58

Download 58 pages 48.77 Kb

Page 17

Connecting video source devices

•If you wish to use this connection method when the projector is in standby mode, make sure the Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings" on page 44 for details.

Connecting video source devices

You need only connect the projector to a video source device using just one of the connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below:

Terminal name	Terminal appearance	Picture quality
HDMI		Best
Component Video		Better
S-Video		Good
Video		Normal

Connecting audio

The projector has built-in mono speaker(s) which are designed to provide basic audio functionality accompanying data presentations for business purposes only. They are not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker(s).

The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.

•The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 17 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 17

Image 17

BenQ MS524/MS514H/MX525/MW526/TW526 user manual Connecting video source devices, Connecting audio

Contents

User Manual MS524/MS514H/MX525/MW526 TW526 Digital ProjectorImportant safety Table of contentsWarranty and Copyright MaintenanceSafety Instructions Important safety instructionsSafety Instructions Continued 3000 m 10000 feet 0 m 0 feet Ceiling mounting the projector Introduction Projector featuresStandard accessories Shipping contentsOptional accessories Power cordFront/upper side Projector exterior viewRear/lower side 10 11Projector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorMS524/MS514H/MX525 Projection dimensionsObtaining a preferred projected image size min. zoom MW526/TW526max. zoom When connecting a signal source to the projector, be sure to Connection2. Use the correct signal cables for each source 1. Turn all equipment off before making any connectionsConnecting audio Connecting video source devicesStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Main menu icon Using the menusMain menu Sub-menuUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function 2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appearsChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratioSetting the User 1/User 2 mode Using Wall ColorOptimizing the image Selecting a picture modeAdjusting Brightness Fine-tuning the image quality in user modesAdjusting Contrast Adjusting Color3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerFreezing the image To cancel the timer, perform the following stepsRemote paging operations Locking control keys Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the test pattern Adjusting the soundAdjusting the sound level Muting the soundLetter Formation Worksheet Coordinate Chart Using the teaching templatesto select Blackboard or Whiteboard TeachingShutting down the projector Direct power offMenu system Menu operationCenter/Top-Left/Top-Right/Bottom Disable/30 min/1 hr/2 hr/3 hr/4 hr/85 sec/10 sec/20 sec/30 sec/Always Reset Lamp Timer SETUPChange Password Main menuDescription of each menu The default setting is Auto and the projector automatically chooses and further fine-tune the image based on the selections listed on the same page below. See Setting the User 1/User 2 mode on pageAdjusts the degree of difference between dark and light in the image Sets the length of time the OSD will remain active after your last key See Setting the Lamp Mode on page 47 for details See Adjusting the sound on page 33 for detailsSee Resetting the lamp timer on page 49 for details See Utilizing the password function on page 22 for detailscarries closed captions Current FunctionSystem StatusCleaning the lens MaintenanceCleaning the projector case Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour whenever you notice that the brightness level has Timing of replacing the lampInstall a new lamp for optimal performance. If the Resetting the lamp timer Replacing the lampPower events IndicatorsLight Status & Descriptionprocedure on page 23 for details TroubleshootingPlease see Entering the password recall Projector specifications SpecificationsCeiling mount installation DimensionsSpecifications 283 mm W x 95 mm H x 222 mm DPixel Timing chartSupported timing for PC input Pixel Supported timing for HDMI HDCP input56 Specifications Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer