Shutting down the projector | BenQ MS524/MS514H/MX525/MW526/TW526

Shutting down the projector

1.Press POWER and a confirmation message will display prompting you. If you don't respond in a few seconds, the message will disappear.

2.Press POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 42 for details.

3.Once the cooling process finishes, a "Power Off

Ring Tone" will be heard. The POWER indicator light is a steady orange and fans stop. Disconnect the power cord from the power outlet.

• To turn off the power ring tone, see "Turning off the Power On/ Off Ring Tone" on page 33 for details.

•If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a

few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

•Lamp life results will vary depending on environmental conditions and usage.

Direct power off

The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes to cool down. In such cases, press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.)

Operation 35

Image 35

BenQ MS524/MS514H/MX525/MW526/TW526 user manual Shutting down the projector, Direct power off

Contents

MS524/MS514H/MX525/MW526 TW526 Digital Projector Table of contents Safety Instructions Important safety instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector features Shipping contents Front/upper side Rear/lower side Projector exterior view Controls and functions Remote control Replacing the remote control batteries Remote control effective range Front Ceiling Positioning your projectorChoosing a location Front Table MS524/MS514H/MX525 Projection dimensionsObtaining a preferred projected image size Average MW526/TW526Screen size Projection distance mm Diagonal Connection Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance Starting up the projector Operation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Below is the overview of the OSD menu Using the menus If you forget the password Using a security cable lockUtilizing the password function Setting a password Disabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details MS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Selecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperature Selection Description Setting the presentation timerResetting current or all picture modes Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the image Operating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keys Turning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound level To select Blackboard or Whiteboard Using the teaching templates Shutting down the projector Direct power off Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Teaching Template Description Save 3D SettingsApply 3D Settings Fine Tuning 3D Color Picture menu Source menu Function Description Picture ModeTemperature Color Temperature Settings System Setup Basic menu Function Description PresentationTimer Installation Screen LockBackground Color Splash Caption System Setup Advanced menu Function DescriptionReset All Closed Status CurrentSystem Care of the projector Maintenance Extending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions KHz Timing chartSupported timing for PC input MAC21 Supported timing for Hdmi Hdcp input MHz Supported timing for Component-YPbPrinputTiming Ntsc Supported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright