Manuals / BenQ / Computer Equipment / Projector

BenQ MS524/MS514H/MX525/MW526/TW526 user manual altitude environment on page 32 for details

Models: MS524/MS514H/MX525/MW526/TW526

1 58

Download 58 pages 48.77 Kb

Page 43

Disables or enables all panel key functions except

4. SYSTEM SETUP: Basic menu 5. SYSTEM SETUP: Advanced menu

Function	Description
Panel Key	Disables or enables all panel key functions except		POWER on the


Lock	projector and keys on the remote control. See "Locking control keys"
	on page 32 for details.
Background	Sets the background color for the projector.
Color

Splash	Allows you to select which logo screen will display during projector
Screen	start-up.

	High	A mode for operation in high altitude areas. See "Operating in a high
	Altitude
	Altitude	altitude environment" on page 32 for details.
	Mode	altitude environment" on page 32 for details.
	Mode

	Audio	See "Adjusting the sound" on page 33 for details.
	Settings	See "Adjusting the sound" on page 33 for details.
	Settings

		Lamp Mode
		See "Setting the Lamp Mode" on page 47 for details.
	Lamp	Reset Lamp Timer
	Settings	See "Resetting the lamp timer" on page 49 for details.
	Settings	Equivalent Lamp
		Equivalent Lamp
		See "Getting to know the lamp hour" on page 47 for details on how the
		total lamp hour is calculated.
	Security	See "Utilizing the password function" on page 22 for details.
	Settings
	Settings

		Selects a baud rate that is identical with your computer’s so that you
	Baud Rate	can connect the projector using a suitable RS-232 cable and update or
	Baud Rate	download the projector’s firmware. This function is intended for

		qualified service personnel.
	Test Pattern	See "Using the test pattern" on page 33 for details.

Operation 43

Image 43

BenQ MS524/MS514H/MX525/MW526/TW526 user manual altitude environment on page 32 for details

Contents

User Manual MS524/MS514H/MX525/MW526 TW526 Digital ProjectorMaintenance Table of contentsImportant safety Warranty and CopyrightSafety Instructions Important safety instructionsSafety Instructions Continued 3000 m 10000 feet 0 m 0 feet Ceiling mounting the projector Introduction Projector featuresPower cord Shipping contentsStandard accessories Optional accessories10 11 Projector exterior viewFront/upper side Rear/lower sideProjector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsMS524/MS514H/MX525 max. zoom MW526/TW526min. zoom 1. Turn all equipment off before making any connections ConnectionWhen connecting a signal source to the projector, be sure to 2. Use the correct signal cables for each sourceConnecting audio Connecting video source devicesStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Sub-menu Using the menusMain menu icon Main menuIf you forget the password Using a security cable lockUtilizing the password function Setting a password2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Optimizing the imageAdjusting Color Fine-tuning the image quality in user modesAdjusting Brightness Adjusting Contrast3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerRemote paging operations To cancel the timer, perform the following stepsFreezing the image To activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentMuting the sound Adjusting the soundUsing the test pattern Adjusting the sound levelTeaching Using the teaching templatesLetter Formation Worksheet Coordinate Chart to select Blackboard or WhiteboardShutting down the projector Direct power offMenu system Menu operation5 sec/10 sec/20 sec/30 sec/Always Disable/30 min/1 hr/2 hr/3 hr/4 hr/8Center/Top-Left/Top-Right/Bottom Main menu SETUPReset Lamp Timer Change PasswordDescription of each menu The default setting is Auto and the projector automatically chooses Adjusts the degree of difference between dark and light in the image same page below. See Setting the User 1/User 2 mode on pageand further fine-tune the image based on the selections listed on the Sets the length of time the OSD will remain active after your last key See Utilizing the password function on page 22 for details See Adjusting the sound on page 33 for detailsSee Setting the Lamp Mode on page 47 for details See Resetting the lamp timer on page 49 for detailscarries closed captions Status FunctionCurrent SystemCare of the projector MaintenanceCleaning the lens Cleaning the projector caseGetting to know the lamp hour Lamp informationExtending lamp life Install a new lamp for optimal performance. If the Timing of replacing the lampwhenever you notice that the brightness level has Resetting the lamp timer Replacing the lampStatus & Description IndicatorsPower events LightPlease see Entering the password recall Troubleshootingprocedure on page 23 for details Projector specifications Specifications283 mm W x 95 mm H x 222 mm D DimensionsCeiling mount installation SpecificationsSupported timing for PC input Timing chartPixel Pixel Supported timing for HDMI HDCP input56 Specifications Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright