This appliance shall be installed only by authorised persons and in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, local water supply regulations, AS/NZS 5601.1-2010-Gas Installations–General installations and any other statutory regulations.

WARNING: It should be recalled that the appliance utilises a threaded 1/2" gas cylindrical male fitting according to UNI-ISO 228-1.

For ease of service, the cooker should be connected with a Flexible Hose, which complies with AS/NZS 1869 (AGA Approved), 10mm ID, class B or D, between 1 - 1.2m long and in accordance with AS5601 for a high level connection.

WARNING: Ensure that the hose is not subjected to abrasion, kinking or permanent deformation and should be able to be inspected along its entire length. Unions compatible with the hose fittings must be used and connections tested for gas leaks. The fixed consumer piping outlet should be at approximately the same height as the cooker connection point, pointing downwards and approximately 200mm - 300mm in from the left hand side of the cooker. The hose should be clear of the floor when the cooker is in the installed position. A hose restraint chain should be anchored to the wall to prevent strain on the hose connections when the cooker is pulled forward.

Fit the supplied gas connectors as shown in Fig. 11 for your installation gas type. The gas inlet has a 1/2" BSP male thread. When making the connection, take care not to apply excessive stress by counterbalancing tightening force. Ensure that the available gas supply is the same as the gas type label affixed near the gas connection point. If not, contact Bertazzoni for a Gas Conversion Kit.

Natural Gas

The natural gas regulator supplied must be fitted for natural gas. Ensure the arrow on the regulator points towards the direction of the gas flow. Commissioning Procedure - The test point pressure must be adjusted to 1.00 kPa with the Wok Burner (both inner and outer), 1× Semi Rapid and Rapid Burner operating on maximum flame.

Propane (LPG)

Fit the LPG test point assembly (supplied in the gas conversion kit). An AGA Approved gas regulator suitable for a supply pressure of 2.75kPa should be part of the gas tank supply.

ANTI-TILTING CHAIN/HOSE RESTRAINING CHAIN

A chain should be fitted by the installer within 50mm of the hose connection point to prevent strain on the hose when the cooker is pulled forward. The chain should restrict the appliance movement to no more than 80% of the hose length. After the chain is installed, check that there is no strain on the hose or gas connections when the cooker is pulled as far forward as the chain allows.

The cooker is also supplied with two chains which are connected to the rear left and right of the appliance. The chains should be connected to the wall directly behind the chains as low as possible to prevent the appliance from tilting forward. If the appliance is installed between two cupboards, drill a hole on each side of the cupboards, pass the chains through the holes and anchor the chains within each cupboard. Ensure the chain connections are strong enough to support the weight of the appliance and taught to prevent it from tilting forward.

WARNING: In order to prevent accidental tipping of the appliance, for example a child climbing onto the open oven door, the stabilising means must be installed. Ensure the chains are correctly anchored to prevent the appliance from tilting forward and to prevent strain on the hose when the cooker is pulled forward.

MAKE SURE THE ANTI-TILTING CHAINS ARE TAUGHT WHEN ANCHORED TO PREVENT THE APPLIANCE TILTING.

ADAPTATION TO DIFFERENT TYPES OF GAS FOR COOKER TYPE M6V

Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity network.

REPLACING THE NOZZLES TO OPERATE WITH ANOTHER TYPE OF GAS FOR COOKER TYPE M6V: Follow the instructions below to change the burner nozzles on the work surface:

1)Pull out the plug from the electric outlet to avoid any type of electric contact.

2)Remove the grids from the work surface.

3)Remove the burners.

4)Unscrew the nozzles using a 7 mm spanner, and replace them (Fig.12) with those needed for the new type of gas according to what is indicated in Table 1.

Follow the instructions below to change the oven burner nozzle:

1)Remove the oven level (Fig. 13).

2)Loosen the screw V and pull out the burner from the support being careful not to damage the ignition plug and the thermocouple (Fig. 14).

3)Unscrew the nozzle R using a 10 mm spanner and replace it with the nozzle needed for the new type of gas according to what is indicated in Table 1

4

Page 3 Page 5
Page 4
Image 4
Bertazzoni X906MFE ANTI-TILTING CHAIN/HOSE Restraining Chain, Adaptation to Different Types of GAS for Cooker Type M6V
Page 3 Page 5

X906 DUAL, X906MFE, X906GEV specifications

The Bertazzoni X906 series, including the X906 DUAL, X906MFE, and X906GEV, represents a pinnacle of kitchen excellence, combining traditional craftsmanship with modern technologies and culinary innovations. These dual-fuel ranges are designed for avid home cooks who value both performance and aesthetics.

At the heart of the Bertazzoni X906 models is the dual-fuel configuration, which seamlessly merges the consistency of electric ovens with the responsiveness of gas cooktops. This dual-fuel capability allows home chefs to experience precise temperature control in the oven and instant heat adjustments on the stove, enhancing the overall cooking experience.

The X906 DUAL stands out with its robust five-burner configuration, providing ample space to accommodate multiple pots and pans simultaneously. Each burner features powerful output, with a high BTU option for quick boiling and a low setting for delicate simmering. Additionally, the continuous cast-iron grates ensure stability and durability while allowing for easy movement of cookware across the cooktop.

The X906MFE model is designed with an emphasis on efficiency and versatility. It features an advanced multi-function electric oven that supports various cooking modes, including convection baking, broiling, and more, allowing users to achieve professional baking results at home. This model also integrates energy-saving technology, ensuring optimal performance while reducing energy consumption.

For those who prioritize style alongside functionality, the X906GEV offers an elegant design that enhances any kitchen decor. With precise finishes and customizable color options, this range allows homeowners to express their personal style. The glass front oven door not only adds to its aesthetic appeal but also provides excellent visibility, allowing users to monitor their dishes without interruption.

The quality construction of the Bertazzoni X906 series includes heavy-duty stainless steel that ensures durability and ease of cleaning. The ranges are equipped with advanced safety features, including flame failure devices and automatic ignition, which manage the ignition of gas burners safely, offering peace of mind while cooking.

In conclusion, the Bertazzoni X906 DUAL, X906MFE, and X906GEV ranges are exemplary choices for those seeking a blend of functionality, efficiency, and elegance in their kitchen. With their innovative features and high-quality construction, these models are designed to inspire culinary creativity and provide professional-level cooking experiences in the comfort of home.
Top Page Image Contents