WARNING: After completing the above-mentioned replacements, the technician must adjust the burners, as described in the paragraph below, seal any adjustment and pre-adjustment devices and apply the label on the appliance, to replace the existing one, corresponding to the new gas adjustment. This label is contained in the spare nozzle bag.

TABLE N°1: Adaption to various types of gas

Burner

Types of Gas

Pressure

Nozzle

Hourly Gas

 

 

 

 

Diameter

Consumption

 

 

 

kPa

mm.

(MJ)

Auxiliary

NG

1.0

0.92

4.2

 

 

LP (Propane)

2.75

0.56

4.0

 

Semi-Rapid

NG

1.0

1.17

6,6

 

 

LP (Propane)

2.75

0.73

6,9

 

Rapid

NG

1.0

1.55

11.5

 

 

LP (Propane)

2.75

0.98

12.3

 

Dual

NG

1.0

0.80

3.1

 

Inner

LP (Propane)

2.75

0.50

3.1

 

Dual

NG

1.0

2x1.14

12.5

 

Outer

LP (Propane)

2.75

2x0.73

13.9

 

Oven

NG

1.0

1.80

16.0

 

 

LP (Propane)

2.75

1.10

16.0

 

BURNER ADJUSTMENT

2) Burner "MINIMUM" adjustment:

Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:

1)Light the burner and set the knob to the MINIMUM position (small flame).

2)Remove the knob of the valve that is press fit on the rod of that valve.

3)If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole on the valve rod (Fig. 15) and turn the choke screw to the right or left until the burner flame is adjusted to minimum. If the cooker is equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see fig. 16).

4)Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

Oven burner adjustment: follow the instructions below to adjust the minimum:

1)Light the burner setting the knob to the MAXIMUM position.

2)Close the oven door and operate the oven for at least 10 minutes.

3)Set the knob to the MINIMUM position (corresponding to 120°) and then remove it.

4)With a slotted screwdriver turn the choking screw (see figure 17) and, while observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM position.

WARNING: The above-mentioned adjustment should be made only with methane gas burners, while for those operating with liquid gas the screw must be locked at the end in a clockwise direction. The grill burner always operates at maximum and therefore no minimum adjustment is required.

APPLIANCE ELECTRIC CONNECTION:

The electric connection must comply with the current legal standards and regulations.

Before making the connection, check that:

-The system electrical rating and the current outlets are adequate for the maximum power output of the appliance (see the label applied to the bottom of the casing).

-The outlet or the system is equipped with an efficient ground connection in accordance with the current legal standards and regulations. The company will not be responsible for the non-compliance with these instructions.

When the connection to the power supply network is made using an outlet:

-If the power cord is supplied without a plug, apply a standard plug that is suitable for the load indicated on the label. Connect the wires according to the diagram shown in FIG.18 and check that:

letter L (phase) = brown wire; letter N (neutral) = blue wire;

ground symbol = green-yellow wire;

-The power cord must be positioned so that an overtemperature of 75 K will not be reached at any point.

-Do not use reductions, adapters or splitters since they might cause false contacts and lead to dangerous overheating.

When the connection is made directly to the electric network:

-Use a device that ensures disconnection from the mains in which the contacts are opened to a distance that permits complete disconnection according to the conditions for over-voltage category III.

-Remember that the ground wire must not be interrupted by the circuit-breaker.

-As an alternative, the electric connection can also be protected by a high-sensitivity residual current circuit-breaker.

-It is highly recommended to attach the special green-yellow ground wire to an efficient ground system.

WARNING: If the power cord is replaced, the ground wire (yellow-green) connected to the terminal, should be longer than the other wires by about 2 cm.

5

Page 5
Image 5
Bertazzoni X906 DUAL, X906GEV, X906MFE manual Burner Adjustment, Appliance Electric Connection, Burner Minimum adjustment

X906 DUAL, X906MFE, X906GEV specifications

The Bertazzoni X906 series, including the X906 DUAL, X906MFE, and X906GEV, represents a pinnacle of kitchen excellence, combining traditional craftsmanship with modern technologies and culinary innovations. These dual-fuel ranges are designed for avid home cooks who value both performance and aesthetics.

At the heart of the Bertazzoni X906 models is the dual-fuel configuration, which seamlessly merges the consistency of electric ovens with the responsiveness of gas cooktops. This dual-fuel capability allows home chefs to experience precise temperature control in the oven and instant heat adjustments on the stove, enhancing the overall cooking experience.

The X906 DUAL stands out with its robust five-burner configuration, providing ample space to accommodate multiple pots and pans simultaneously. Each burner features powerful output, with a high BTU option for quick boiling and a low setting for delicate simmering. Additionally, the continuous cast-iron grates ensure stability and durability while allowing for easy movement of cookware across the cooktop.

The X906MFE model is designed with an emphasis on efficiency and versatility. It features an advanced multi-function electric oven that supports various cooking modes, including convection baking, broiling, and more, allowing users to achieve professional baking results at home. This model also integrates energy-saving technology, ensuring optimal performance while reducing energy consumption.

For those who prioritize style alongside functionality, the X906GEV offers an elegant design that enhances any kitchen decor. With precise finishes and customizable color options, this range allows homeowners to express their personal style. The glass front oven door not only adds to its aesthetic appeal but also provides excellent visibility, allowing users to monitor their dishes without interruption.

The quality construction of the Bertazzoni X906 series includes heavy-duty stainless steel that ensures durability and ease of cleaning. The ranges are equipped with advanced safety features, including flame failure devices and automatic ignition, which manage the ignition of gas burners safely, offering peace of mind while cooking.

In conclusion, the Bertazzoni X906 DUAL, X906MFE, and X906GEV ranges are exemplary choices for those seeking a blend of functionality, efficiency, and elegance in their kitchen. With their innovative features and high-quality construction, these models are designed to inspire culinary creativity and provide professional-level cooking experiences in the comfort of home.