Manuals / Billion Electric Company / Computer Equipment / Network Router

Billion Electric Company 8501 user manual SHDSL - BiPAC, wired Mode

Models: 8501

1 134

Download 134 pages 2.47 Kb

Page 50

4-wired Mode

SHDSL VPN Firewall Bridge/Router

SHDSL – BiPAC 8520

4-wired Mode	2-wired Mode

4-Wired Connection: BiPAC 8520 supports either 2-wire and 4-wires SHDSL connection. Activate the device to 4-wired by enabling the function; otherwise, disable it to be used as 2-wire mode connection.

Note: When select 2-wired mode, only Port 1 settings need to be configured and the SHDSL (RJ-11 cable) must be connected to LINE 1 on the back of the device.

Mode: The SHDSL device can function as a CPE (Customer Premises Equipment) or CO (Central Office). Select CPE mode when the BiPAC 8500 is connecting to your ISP.

Back – to –back: it is a direct connection between two SHDSL devices which one is set to CPE and the other is CO by using a standard RJ-11 telephone cable.

Annex Type: It is the DSL operating mode standard. Select Annex A or Annex B to support up to 2.3Mpbs (for 2-wired mode) and 4.6Mpbs (for 4-wired mode). Select other annex such as Annex B_ANFP / Annex A_B_ANFP, you may consult with your ISP first.

Back – to –back: to be sure the Annex type is the same on the BiPAC 8520 and the remote router.

Bit Rate Mode: The mode selections are Adaptive and Fixed. Selecting the Adaptive mode, the best connection rate will be automatically negotiated with the CO / ISP. Selecting the Fixed mode, the connection rate will be fixed to the specific fixed bit rate selected with the CO / ISP.

Fixed Bit Rate: Specify the fix transfer rate when Fixed Mode is selected. Specify the maximum transfer rate when Adaptive Mode is selected. Bit Rate range is from 72kbps ~ 2368kbps.

Activate Line: Line active true is set by default. Select false to disable and true to enable SHDSL SHDSL connection

Note: Once Active Line is selected as false, you must enable the Active Line to true again and click Apply button to reactivate SHDSL connection.

DSP FirmwareVersion: Display the SHDSL line code firmware version.

Connected: Display current SHDSL line sync status.

State: Display current SHDSL line status.

Bit Rate: Display SHDSL line synch speed rate.

Click Apply button to apply your changes

49

Chapter 4: Configuration

Image 50

Billion Electric Company 8501 user manual SHDSL - BiPAC, wired Mode

Contents

User’s Manual BiPAC 8500/8501/8520SHDSL VPN Firewall Bridge Router Version ReleaseTable of Contents Time Schedule QoS Quality of ServiceCHAPTER 5 TROUBLESHOOTING AdvancedIntroduction to your Router FeaturesChapter 1 Introduction Fast Ethernet SwitchDynamic Domain Name System DDNS Dynamic Host Configuration Protocol DHCP client and serverDomain Name System DNS relay Virtual Private Network VPNFirmware Upgradeable Rich Management InterfacesPackage Contents Chapter 2 Installing the RouterImportant note for using this router Do not use this router in high humidity or high temperaturesLit when the system is ready The Front LEDs of BiPACLit when power is ON Chapter 2 Installing the RouterLED LINE 1 LAN Port 1X - 4X RJ-45 connectorThe Front LEDs of BiPAC SYS PWRLED PWR SYS LAN Port 1X - 4X RJ-45 connectorThe Front LEDs of BiPAC LINE5 CONSOLE LINE 6 1X - 2X RJ-11 connector The Rear Ports of BiPAC 8500Port 1 Power Switch 2 PWR 3 RESET LAN 4 1X ＊Only the BiPAC 8520 has two Line jack ports. BiPAC 8500 has onePort 1 Power Switch 2 PWR 3 RESET LAN 4 1X - 4X RJ-45 connector The Rear Ports of BiPACCabling 5 CONSOLE 6 LINEChapter 3 Basic Installation Connecting Your Router4. Select Internet Protocol TCP/IP and click Properties. See Figure Configuring PCs in Windows in Window XP2. Double-click Local Area Connection. See Figure 4. Select Internet Protocol TCP/IP and click Properties See Figure Configuring PCs in Windows2. Double-click Local Area “LAN” Connection. See Figure 3. Click Properties Configuring PC in Windows 95/98/ME5. Then select the DNS Configuration tab. See Figure 2. Select TCP/IP Protocol and click Properties. See Figure Configuring PC in Windows NT4.0Chapter 3 Basic Installation SHDSL VPN Firewall Bridge/RouterDevice LAN IP settings Factory Default SettingsWeb Interface Username and Password ISP setting in WAN siteRFC 1483 Routed IPoA Routed IP over ATM Information from your ISPPPPoE PPPoE / PPPoE with Pass-through PPPoA RFC 1483 Bridged Configuring with your Web Browser Congratulation! You are now successfully logon to the SHDSL RouterSave Config to FLASH Chapter 4 ConfigurationQuick Start Configuration StatusRouting Table StatusARP Table Routing TableLeased Table DHCP TablePPTP Status Expired TableIPSec Status L2TP Status Email StatusError Log Event LogChapter 4 Configuration DiagnosticNAT Sessions SHDSL VPN Firewall Bridge/RouterSHDSL VPN Firewall Bridge/Router UPnP PortmapChapter 4 Configuration Quick Start Chapter 4 Configuration SHDSL VPN Firewall Bridge/RouterBridge Interface ConfigurationLAN Local Area Network Primary IP Address Chapter 4 ConfigurationEthernet SHDSL VPN Firewall Bridge/RouterIP Alias Ethernet Client Filter → Active PC in LANEthernet Client Filter Default setting is set to Disable Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Port Setting DHCP Server WAN - Wide Area Network RFC 1483 Routed Connections IP AssignmentRFC 1483 Bridged Connections All Ip PppoePPPoA Routed Connections ConnectionAdvanced Options PPPoA IPoA Routed Connections IP AssignmentPPPoE Connections ConnectionChapter 4 Configuration Advanced Options PPPoEPPPoE with Pass-through Connections Advanced Options PPPoE Chapter 4 ConfigurationConnection Page SHDSL - BiPAC SHDSL - BiPAC 4-wired Mode2-wired Mode SHDSL - BiPAC System Time ZoneRemote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings SHDSL VPN Firewall Bridge/Router Chapter 4 ConfigurationPacket Filter Application Example Predefined Port Filters RulesTable 1 Predefined Port Filter ProtocolUDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Configuring Packet Filter Click DeleteClick Add TCP/UDP Filter ExampleSHDSL VPN Firewall Bridge/Router Chapter 4 Configuration5. The new port filter rule for HTTP is shown below Intrusion Detection Block DurationDetect Parameter Table 2 Hacker attack types recognized by the IDSIntrusion Name Ascend KillURL Filter 3. If the packet does not match either of the above two items, it is sent to the remote web server IM / P2P Blocking Instant Message Blocking The default is set to DisabledPeer to Peer Blocking The default is set to Disabled Log information can be seen in the Status - Event Log after enabling Chapter 4 ConfigurationFirewall Log SHDSL VPN Firewall Bridge/RouterVPN - Virtual Private Networks PPTP Point-to-Point Tunneling ProtocolPPTP Connection - Remote Access Chapter 4 Configuration Dial-outExample Configuring a Remote Access PPTP VPN Dial-out Connection SHDSL VPN Firewall Bridge/RouterDescription Configuring the PPTP VPN in the OfficeFunction PPTP Connection - LAN to LAN SHDSL VPN Firewall Bridge/Router Example Configuring a PPTP LAN-to-LAN VPN ConnectionChapter 4 Configuration Configuring PPTP VPN in the Head Office FunctionDescription Description Configuring PPTP VPN in the Branch OfficeFunction IPSec IP Security Protocol IPSec VPN Connection Chapter 4 ConfigurationSelect the Apply button to apply your changes Advanced Option IKE ProposalPing to Keep Alive Local IDRemote ID Ping to the IPTunnel mode ESPMD5 with AES Table 3 Network Configuration and Security PlanExample Configuring a IPSec LAN-to-LAN VPN Connection Tunnel mode ESPMD5 with AESDescription Configuring IPSec VPN in the Head OfficeFunction Description Configuring IPSec VPN in the Branch OfficeFunction SHDSL VPN Firewall Bridge/Router Example Configuring a IPSec Host-to-LAN VPN ConnectionChapter 4 Configuration Description Configuring IPSec VPN in the OfficeFunction L2TP Layer Two Tunneling Protocol L2TP Connection - Remote Access L2TP VPN ConnectionL2TP over IPSec L2TP/IPSec VPN Connection Chapter 4 Configuration Dial-inExample Configuring a L2TP VPN - Remote Access Dial-in Connection SHDSL VPN Firewall Bridge/RouterDescription Configuring L2TP VPN in the OfficeFunction Dial-out Example Configuring a Remote Access L2TP VPN Dial-out ConnectionChapter 4 Configuration SHDSL VPN Firewall Bridge/RouterDescription Configuring the L2TP VPN in the OfficeFunction SHDSL VPN Firewall Bridge/Router Example Configuring your Router to Dial-in to the ServerChapter 4 Configuration L2TP Connection - LAN to LAN L2TP VPN ConnectionL2TP over IPSec L2TP/IPSec VPN Connection Example Configuring L2TP LAN-to-LAN VPN Connection Chapter 4 ConfigurationDescription Configuring L2TP VPN in the Head OfficeFunction Description Configuring L2TP VPN in the Branch OfficeFunction Prioritization QoS Quality of ServiceClick Clear HighSHDSL Router Device Table 4 DSCP Mapping TableDSCP Mapping Table Standard DSCPClick Clear Outbound IP Throttling LAN to WANClick Clear Inbound IP Throttling WAN to LANInformation and Settings VoIP Normal PCs Restricted PCConnection Diagram Chapter 4 ConfigurationVoice application Advanced setting by using IP throttlingMission-critical application Restricted ApplicationChapter 4 Configuration SHDSL VPN Firewall Bridge/RouterVirtual Server “Port Forwarding” Add Virtual Server Internal IPExample IP AddressEdit DMZ Host Edit One-to-One NAT Network Address Translation Global IP AddressSelect the Apply button to apply your changes Port Number Table 5 Well-known and registered PortsExample List of some well-known and registered port numbers ProtocolTime Schedule Edit a Time Slot Click EditConfiguration of Time Schedule Delete a Time SlotAdvanced Management, IGMP and VLAN Bridge Static RouteDynamic DNS Check Email Device Management Embedded Web Server 2 Management IP accountsSNMP Universal Plug and Play UPnPSNMP V1 and SNMP Version SNMPv2c and SNMPv3From RFC 1471 PPP/LCP MIB From RFC1650 EtherLike-MIBFrom RFC 1493 Bridge MIB From RFC 1472 PPP/Security MIBGo to Configuration LAN Bridge Interface Advanced VLAN Setup Example Triply PlayStep 1 Setup Member Ports IGMPVLAN Port Always starts with Go to Configuration WAN ISPBridge Interface Step 2 Create WAN InterfacePppoe From the example Step 3 Setup VLAN ServiceGo to Configuration Advanced VLAN Bridge Go Configuration Advanced IGMP Save Configuration to FlashStep 4 IGMP Snooping Enable Logout Problems with the WAN Interface Chapter 5 TroubleshootingProblems starting up the router Problems with the LAN InterfaceWORLDWIDE APPENDIX A Product Support and Contact InformationContact Billion AUSTRALIA