9GENERAL SAFETY
For your safety and the safety of others, these directions should be followed:
Do not operate this machine without first reading owner's manual and engine manufacturer's manual.
Use of Ear Protection is recommended while operating this machine.
Use of Eye and Breathing protection is recom- 
mended when using this machine, especially in dry
and dusty conditions.
·DO NOT place hands or feet inside nozzle intake opening, near debris outlet or near any moving parts.
·DO NOT start engine without hose and exhaust elbow connected firmly in place to housing and exhaust outlet.
·DO NOT operate without discharging exhaust into enclosed container.
·DO NOT operate during excessive vibration.
·DO NOT remove hose until engine has been turned off and has come to a complete stop.
·DO NOT operate machine with hose or exhaust elbow removed. ·DO NOT use this machine for vacuuming exclusively sand, dust, fine dirt, rock, glass, string like material, grain, rags, cans, metal, bark or water.
·DO NOT operate this machine on slopes greater than 20%. ·DO NOT pick up any hot or burning debris, or any toxic or explosive material.
·DO NOT allow children to operate this equipment.
10ASSEMBLY
Read all safety and operating instructions before assembling or starting this unit.
PUT OIL IN ENGINE BEFORE STARTING.
Your Billy Goat is shipped from the factory in one carton and is completely assembled except for the exhaust elbow, nozzle, handle loop for nozzle, hose booms, hose bands, hose coupler, hose clamps and related hardware.
1.ASSEMBLE exhaust elbow (item 10), to main unit and firmly tighten knobs (item 90), that are preassembled to main unit.
2.SECURELY ATTACH unit to tailgate of a truck or to a trailer, so that the exhaust discharges into an enclosed container.
3.ATTACH hose to hose coupler (item 24), using hose clamp (item
60)NOTE: This unit is equipped with a unidirectional hose. Assemble hose so that interior hose material seams face toward unit.
4. ASSEMBLE hose coupler to housing of main unit and securely tighten knob (item 13), that is preassembled to housing front plate.
5.ASSEMBLE nozzle handle loop (item 82), to nozzle handle using screw (item 80), washer (item 6) and lock nut (item 5). Adjust handle loop to desired height and angle and securely tighten in place.
6.ASSEMBLE nozzle handle (item 78), to nozzle (item 77), using screws (item 80), washers (item 79), washers (item 4) and lock nuts (item 5).
7.ATTACH assembled nozzle to hose using hose clamp (item 60). Before tightening hose clamp, position nozzle handle upward when hose is stretched to prevent twisting load on hose assembly during operation.
8.ASSEMBLE tube square boom (item 51), to boom pivot (item 50), using chain loop assembly (item 54), washers (item 4) and lock nut (item 52).
9.ASSEMBLE remaining chain loop assembly (item 54), to end of tube square boom (item 51) using washer (item 4) and lock nut (item 52).
10.SLIDE boom assembly into square tube on front of housing.
11.ASSEMBLE hose bands (item 56) around hose and onto chain loop assemblies on boom assembly using screws (item 55) and lock nuts (item 52) (see ADJUSTING HOSE BOOM on page 5).
11PACKING CHECKLIST
TR MODELS
Briggs & Stratton 11 HP
These items should be included in your carton. If any of these parts are
Boxing Checklist
Honda 13 HP
HTR MODELS
Briggs & Stratton
Hose 8"x 12.5'
P/N 810523
Handle Loop Nozzle P/N 811019
Parts Bag &
Literature Assy
P/N 811128
Parts Bag
&Literature Assy
Engine
Manual Per
Model
missing, contact your dealer.
Check
10
51
50
56
59
60
78
77
Exhaust Elbow 811191
Boom Square Arm 810875
Boom Pivot WA 810870
Band Hose Boom 8" (203mm) 810880 Qty. 2
Coupler Weld Assy. 8"(203mm) 811170
Hose Clamps 8"(203mm) 810566 Qty. 2
Handle Nozzle 811020
Nozzle 8"(203mm) 811007
Part No. 811237 | Page 3 of 12 | Form No. F050304A |
