Billy Goat KD 410 specifications Disconnect Spark Plug Wire Before Servicing Unit, Description

Item	16	PARTS	Description	KD410	QTY
No.		LIST		Part No.
1	TURF QUICK DEBRIS BAG (SEE ACCESSORIES FOR OTHER OPTIONS)			890305	1
4	NUT LOCK (1/4 - 20)			*8160001	6
5	SCREW CAP ( 1/4 - 20 x 1-1/2 HEX )			*8041008	4
6	HANDLE ASS’Y (incl. items 5(5),11(2))			900054	1
7	AXLE HEIGHT ADJUST			890389	1
8	SCREW HANDLE 5/16 - 18 x 1 3/4			*8041031	1
9	SCREW HANDLE 5/16 - 18 x 2 1/2			*8041034	1
11	BAR BAG SUPPORT			900039	2
12	DOOR EXHAUST ASS’Y (incl. item 62 )			890148	1
14	BOLT-CARRIAGE 1/4x3/4			*8024021	2
16	WASHER 1/4 FC ZP			*8171002	2
18	BRACKET - HEIGHT ADJUSTMENT			890021	1
20	SPRING			900136	1
21	TIRE - ONLY (PER ASSY)			900507	1
22	PIN - HAIR COTTER			900471	1
23	CABLE HEIGHT ADJUSTMENT			890019	1
24	BOLT - CARRIAGE 5/16 - 18 x 4 1/2			*8024054	4
26	NUT LOCK 5/16 - 18 HEX			*8160002	4
27	HANDLE LOWER KD510			890346	1
28	PLATE HANDLE SUPPORT			900933	1
29	LABEL DANGER CUT FINGER			400424	2
30	WASHER FLAT CUT 5/16			*8171003	2
32	ROPE GUIDE			830533	2
34	WHEEL ASS’Y		(incl. items 21)	900509	4
35	WASHER 0.75 “C”			900997	0-1
40	SCREW CAP 1/4 - 20 x 1 - 1/4			*8041007	4
42	SCREW SELF TAPPING 10 - 24 x 1/2			*8123086	1
43	NOZZLE MAINFRAME ASS’Y (incl. one of items 29,44,42)			890391	1
44	PLUG			900146	1
45	SCREWCAP 1/4-20 X 1 3/4			8041009	1
47	IMPELLER ASS’Y (incl. items 49, 50, 51, 59 )			900168	1
49	KEY			900162	2
50	WASHER LOCK 3/8 TWISTED TOOTH			400502	1
51	SCREW CAP 3/8 -24 x 1 (HARDENED)(TORQ.50 FT-LBS)(68N.m)			900154	1
52	HOUSING ASS’Y (incl. items 12, 14, 15, 16, 86)			890371	1
53	ENGINE BRIGGS AND STRATTON 4 HP QUATTRO			890565	1
56	SCREW CAP 3/8 - 1-1/2 TAPTITE			890408	3
58	WASHER FLAT 1/2 SAE			*8172011	4
60	HT ADJUST ASSY			890013	1
61	1/2-13 CAP NUT NP W/PATCH			890530	4
62	LABEL DANGER FLYING MATERIAL			810736	1
63	LABEL DO NOT FILL WHEN ENGINE IS HOT			400268	1
68	PLATE TOP ASS’Y (incl. items 14, 15, 29, 48, 69, 70, 71, 72)			890402	1
71	SCREW CAP 1/4 - 20 x 1/2 HWH			890359	15
74	NUT LOCK 5/16 - 18 THIN HT.			*8161041	2
76	PLATE UPPER HEIGHT ADJUST			890005	1
83	CONNECTOR BAG QUICK			890176	1

*Denotes standard hardware item that may be purchased locally.

17MAINTENANCE

Use only a qualified mechanic for any adjustments, disassembly or any kind of repair .

WARNING: TO AVOID PERSONAL INJURY, ALWAYS

TURN MACHINE OFF, MAKE SURE ALL MOVING

PARTS COME TO A COMPLETE STOP.

DISCONNECT SPARK PLUG WIRE

BEFORE SERVICING UNIT.

ENGINE: See engine manufacturer operator's instructions.

DEBRIS BAG: See page 5.

RECONNECT SPARK PLUG WIRE,

GUARDS, BAG, CAPS AND / OR

HOSE BEFORE STARTING ENGINE.

17.1IMPELLER REMOVAL

1.Wait for engine to cool and disconnect spark plug.

2. Drain fuel and oil from the engine.

3.Remove bag, quick release, and upper handle.

4. Remove housing top plate by removing bolts around outside of housing.

5.Leaving engine fastened to top plate, remove impeller bolt and lock washer and slide impeller off crankshaft (A puller may be required).

6.If impeller slides off freely, proceed to step 9.

(Do not drop impeller).

7.If impeller does not slide off crankshaft, place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck impeller.

8.If the impeller cannot be loosened, obtain a 1” (25.4mm) longer bolt of the same diameter and thread type as the impeller bolt. Invert engine and impeller and support engine above ground to prevent recoil damage. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or wheel puller against the bolt head and the impeller back-plate (near the blades), remove impeller from shaft.

Part No. 890564 Page 7 of 8 Form No. F022502A