90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 4
•Note: To ensure maximum battery life do not overcharge. Only charge until the green LED charge status indicator lights.
•Do not expose charger to rain or snow. Use in a dry location only.
•Do not crush, cut, pull or expose charger cords to extreme heat.
•Position charger cords so they do not become entangled or become a safety hazard. Keep charger cords away from sharp edges.
•To reduce risk of damage to plug and cord, pull by plug rather than cord when disconnecting unit from the charger.
•Use of improper extension cord could result in a risk of fire, electric shock or electrocution.
•Use only the supplied chargers when charging this spotlight. The use of any other charger could damage the spotlight or create a hazardous condition.
•Use only one charger when charging.
•Do not attempt to charge the unit if the charger plug is damaged— return the unit to manufacturer for repair.
•Do not attempt to open the charger. There are no customer serviceable parts inside. Return to manufacturer for repair.
•All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connection to a power source or load.
•After charging/recharging, disconnect charger or extension cord and wait 5 minutes before use.
•This unit contains a
•FIRST AID – SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention.
EYES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate medical attention.
IMPORTANT:
•This unit is delivered in a partially charged state. Fully charge unit for
•Read And Understand This Instruction Manual Before Using This Unit.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Thank you for choosing the Black & Decker®
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120 Volt AC Charger for
Charging/Recharging Using the 120 Volt AC
Charger and a Standard Household
Extension Cord (not included)
Plug a standard North American 120 volt AC extension | CHARGE STATUS LED |
cord (not included) into the 120 Volt AC Charger on the | INDICATORS |
back of the unit. |
|
Make sure the Spotlight is OFF (the Trigger Lock is in the OFF | |
position and the Trigger is not depressed). | |
Charge for | CHARGER |
| |
Indicator lights. |
|
Notes: To extend battery life, disconnect the charger after 48 hours.
All batteries lose charge with time, especially when they are warm. Recharge the unit every two months for
If the unit is not going to be used for extended periods, disconnect the charger and store in a cool, dry place.
Charging/Recharging Using the 12 Volt DC Charging Adapter
Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port (shown in the illustration below).
12 VOLT DC CHARGING PORT (UNDERSIDE OF UNIT)
12 VOLT DC CHARGING ADAPTER
Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.
FEATURES
•Powerful, focused quartz halogen beam with Dimmer Switch for high and low settings
•Safety cap protects 120 volt AC charger
•Comfortable pistol grip, handle and carry lanyard
•Charge Status LED Indicator
•UL listed,
•12 volt DC charging adapter included
•Rechargeable,
Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).
Charge until the green Charge Status LED Indicator lights.
Notes:When using a vehicle’s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the accessory outlet.
To avoid deeply discharging your vehicle battery we recommend to have the vehicle running while recharging the light with the DC recharge adapter.
WARNING: NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.
Controls and Functions
DIMMER SWITCH | CARRY HANDLE |
CHARGE STATUS LED | |
| INDICATOR |
| 120 VOLT AC CHARGER |
| (BACK OF UNIT) |
QUARTZ HALOGEN BULB |
| CARRY LANYARD |
|
| |
|
| TRIGGER LOCK |
12 VOLT DC CHARGING PORT |
| PISTOL GRIP HANDLE |
(UNDERSIDE OF UNIT) | ON/OFF | |
| TRIGGER |
|
OPERATING INSTRUCTIONS
The Trigger Switch is located on the front of the
•Turn on the Spotlight by squeezing the ON/OFF Trigger.
•Turn off the Spotlight by releasing the ON/OFF Trigger.
To lock the Trigger in the ON position for continuous operation, squeeze the ON/OFF Trigger and slide theTrigger Lock Button located on the side on the handle DOWN (refer to the “Controls and Functions” illustration). The Spotlight will stay ON until you slide the Trigger Lock Button back UP.
Dimmer Switch
The Dimmer Switch is located on the top of the Spotlight (refer to the “Controls and Functions” illustration). Sliding the switch forward (toward the Spotlight bulb) sets the Spotlight on High Beam; sliding the switch backward sets the Spotlight on Low Beam.
Using the Carry Handle as a Stand For Hands-Free Operation
Invert the unit to use the Carry Handle as a stand, and set it upon a flat, stable surface for
Using the Built-In Carry Lanyard
The Carry Lanyard may be used to store or carry the Spotlight; and also allows you to position the Spotlight for convenient,
4 | 5 | ||
|
|
|
|
|
|
|
|
|
|
|
|
