Black & Decker CHV9610, CWV9610 instruction manual Assembly, Use

90564313 CHV9610 CWV9610 VAC manual.qxd:??????-00 Cir Saw book 5/10/10 11:30 AM Page 4

Assembly

Wall Mounting
	B	C
The product can be wall mounted, if desired,
using the wall mount bracket, screws and
anchors supplied. To wall mount the vac, refer
to figures B, C, D and E.

• Figure B - Mark the location of the screw

holes (within reach of an electrical outlet for

chargeing the vac while it is on the wall

bracket).

• Figure C - Insert the charger cord into the

curved slot in the wall mount bracket leaving

approximately 8-9 inches (203mm - 227mm)

Use

Switching on and off

•Figure G - To start, slide the On/Off switch forward (i.e. “O”= Off, “I” = On).

•To stop, slide the switch back.

•Return the product to the charger immediately after use so that it will be ready and fully charged for the next use. Ensure that the product is fully engaged with the power supply plug.

DRY PICK-UP(Catalog Number CHV9610)

• For everyday spills of dry material.

G

excess as shown.

• Figure D - Hang the vac on the wall by placing the opening on the	D
base of the vac over the hooks in the wall mount bracket as shown in
figure D.

• Figure E - Insert the jack plug into the	E
charging socket.

Charging the battery

From new, the rechargeable cells of the product need a minimum charge time of 24 hours to ensure full power.

We suggest you fully discharge the product when it is used for the first time as this will help the cells recharge faster.

•The switch must be in the off (“O”) position, the product will not charge if it is in any other position. F

•Figure F - Plug the jack plug of the charger into

the charging socket of the tool. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. The charging indicator will be lit.

While charging, the charger may get warm, this is perfectly normal and safe. It can remain on charge indefinitely without damage or danger. It is not possible to “overcharge” the battery cells with the charger provided.

•The charging indicator will be lit as long as the appliance is connected to the plugged-in charger.

WARNING: Do not charge the battery at ambient temperatures below 39°F (4°C) or above 104°F (40°C).

4

WET AND DRY PICK-UP(Catalog Number CWV9610)

•For everyday spills of dry material, use your appliance without the squeegee accessory. CAUTION: Your product is designed for light spills only.

•This vacuum can also be used to pick up everyday liquid spills. Use the squeegee accessory on non-absorbent, hard surfaces. On absorbent surfaces, such as carpet, your appliance will pick up wet spills better without the accessory.

•For best performance on hard surface wet pickups, insert squeegee into the bowl nozzle opening.

•For best results when using this accessory, hold the appliance at an angle of 45° and pull it slowly towards you.

•Do not fill the bowl beyond the end of the intake chute. If there is any liquid in the bowl, do not turn the unit upside down, sideways, point the nozzle upward, or shake the vac excessively.

•After picking up liquid substances clean the vac and filter immediately. Mold and mildew may form if the unit is not properly cleaned after wet pickups.

•If charging in a vertical position, be sure to empty all liquid contents to avoid damage to your appliance.

Cleaning the product (figures H, I, J and K)

WARNING: Never use the vac without its filter.

NOTE: The filter is re-usable, do not confuse it	H
with a disposable dust bag, and do not throw it
away when the product is emptied. We
recommend that you replace the filter every 6-9
months depending on frequency of use.

•Figure H - Remove the dust bowl by pressing the bowl release button and pulling the bowl straight off.

•To replace the dust bowl, place it back onto the handle until it “clicks” firmly into position.

5