ENGLISH

Thank you for purchasing this Price Pfister Lavatory Faucet. All Price Pfister products are carefully engineered and factory tested to provide long trouble-free use under normal conditions. This Lavatory Faucet is easy to install using basic tools and our easy to follow illustrated instructions. If you have any questions regarding your Lavatory Faucet installation, call 1-800-Pfaucet (1-800-732-8238).

1 BEFORE PROCEEDING

 

 

4B

 

WARNING: Read all the instructions completely before proceeding.

 

4B3

 

 

 

Price Pfister recommends calling a professional if you are uncertain about

 

 

4B2
installing this product!

 

 

 

 

 

 

4B4

This product should be installed in accordance with all local and state plumbing and

 

 

building codes.

 

 

 

4B1

2

 

 

 

4B5

 

 

 

4B INSTALLING FAUCET WITH DECKPLATE

 

 

 

Ensure that the Plastic Putty Plate (4B1) is pressed on the Deckplate (4B2).

 

 

 

Place a bead of plumber’s putty in the groove along the outer edge of the Putty

 

 

 

Plate (4B1). Assemble Deckplate and Putty Plate to Faucet Body (4B3). With

 

 

 

the handle and spout facing forward, carefully install the Faucet Supply Tubes
2 SHUT OFF WATER SUPPLY

 

 

(4B4) through the center hole of sink (4B5).

 

 

4C

 

Locate water supply inlets and shut off the water supply valves. These are

 

4C3
usually found under the sink or near the water meter. If you are replacing an

 

existing faucet, remove the faucet from the sink and clean the sink surface

 

 

 

thoroughly.

 

 

 

4C2

3

 

 

 

4C4

 

 

 

4C1

 

 

 

 

4C5

 

 

 

4C INSTALLING FAUCET WITH SOAP DISPENSER

 

 

 

Ensure that the Plastic Putty Plate (4C1) is pressed on the Deckplate (4C2).
3 TOOLS RECOMMENDED

 

 

Place a bead of plumber’s putty in the groove along the outer edge of the Putty

 

 

Plate (4C1). Assemble Deckplate and Putty Plate to Faucet Body (4C3). With
• PTFE plumber's tape or thread sealant• Plumber's putty

 

the handle and spout facing forward, carefully install the Faucet Supply Tubes

• Slotted screwdriver• Phillips head screwdriver• Pliers

 

(4C4) through the center hole of sink (4C5).
• Adjustable wrench • Flashlight• Cloth

 

5

 

Your installation may require supply lines and/or shut-off valves, cone washers,

 

 

friction rings, or other additional tools. Consult the store where your faucet was

 

 

 

purchased for recommended connections that may be required for you area.

 

 

 

FAUCET INSTALLATION STEPS

 

 

 

4A

 

 

 

 

4A2

 

 

 

5C

 

 

 

 

4A1

 

 

 

 

4A44A3

 

 

5A

 

 

 

 

 

 

 

 

 

 

 

5B

 

 

 

 

5D

 

 

 

5 SECURING FAUCET

 

 

 

From underneath sink, secure the faucet by placing the Metal Washer (5A)
4A INSTALLING FAUCET WITH SINGLE HOLE MOUNTING

 

and the Long Nut (5B) ( 7/16 hex.) onto the Mounting Post (5C). Make sure

 

that the bumps on the Metal Washer (5A) are facing up. Tighten using a flathead
Assemble Base Washer (4A1) to Faucet Body (4A2). With the handle and

 

screwdriver or an adjustable wrench until the faucet is firmly connected to the
spout facing forward, carefully install the Faucet Supply Tubes (4A3) through

 

sink. Secure connection by screwing the Setscrew (5D) onto the Long Nut
the center hole of sink (4A4).

 

2

(5B). Do not over tighten!