4. The line cutter on the edge of the guard can dull over time. It is recommended you periodically
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
Troubleshooting |
| |||
trimmer runs slowly |
| |||
• | Unplug the trimmer. |
|
| |
• | Check that the spool housing can rotate freely. Carefully clean it if necessary. | |||
• | Check that the cutting line does not protrude more than approximately | |||
| from the spool. If it does, cut it off so that it just reaches the line trimming blade. | |||
Automatic line feed does not work | ||||
• | Unplug the trimmer. |
|
| |
• | Remove the spool cap. |
|
| |
• | Pull the cutting line until it protrudes approximately | |||
• | insufficient cutting line is left on the spool, install a new spool of cutting line. | |||
Ensure that the line is not crisscrossed on the spool as detailed in figure Q. If it is, unwind | ||||
• | the cutting line, then wind it back on the spool neatly so that the lines do not cross. | |||
Ensure the beginning of the cutting line is pulled tight against the spool as shown in figure P. | ||||
• | Align the tabs on the spool cap with the cut outs in the housing. | |||
• | Push the spool cap onto the housing until it snaps securely into place. | |||
• | If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade. | |||
| If the automatic line feed still does not work or the spool is jammed, try the following suggestions: | |||
| • | Carefully clean the spool and housing. |
| |
| • | Remove the spool and check if the lever in the spool housing can move freely. | ||
| • | Remove the spool and unwind the cutting line, then wind it on neatly again. Replace the | ||
|
| spool into the housing. |
| |
Problem | Possible Cause | Possible Solution | ||
• | trimmer will not start. | • Cord not plugged in. | • Plug trimmer into a working outlet. | |
|
|
| • Circuit fuse is blown. | • Replace circuit fuse. (If the product |
|
|
|
| repeatedly causes the circuit fuse to |
|
|
|
| blow, discontinue use immediately and |
|
|
|
| have it serviced at a Black & Decker |
|
|
|
| service center or authorized servicer.) |
|
|
| • Circuit breaker is tripped. • Reset circuit breaker. (If the product | |
|
|
|
| repeatedly causes the circuit breaker to |
|
|
|
| trip, discontinue use immediately and |
|
|
|
| have it serviced at a Black & Decker |
|
|
| • Cord or switch is | service center or authorized servicer.) |
|
|
| • Have cord or switch replaced at Black | |
|
|
| damaged. | & Decker Service Center or Authorized |
• | Cutting line is consumed • Edging too far from | Servicer | ||
• Ensure edging wheel is on the edge of | ||||
| quickly in edge mode. | edge of sidewalks or | the surface and the cutting line is positioned | |
|
|
| abrasive surfaces. The | in the grass or dirt area to be edged not |
|
|
| cutting line is hitting the | the sidewalk or other abrasive surface. |
|
|
| sidewalk or abrasive surface. |
|
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power trimmer service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, call:
9