3 - EN
2 Installation
Refer to the nearest Authorised Service Agent
for installation of the product. To make the
product ready for use, review the information
in the user manual and make sure that the
electricity, tap water supply and water drainage
systemsareappropriatebeforecallingthe
AuthorizedServiceAgent.Iftheyarenot,call
aqualifiedtechnicianandplumbertohaveany
necessary arrangements carried out.
C Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer's
responsibility.
B Installationandelectricalconnectionsof
theproductmustbecarriedoutbythe
Authorized Service Agent. Manufacturer
shallnotbeheldliablefordamagesthat
mayarisefromprocedurescarriedoutby
unauthorized persons.
A Prior to installation, visually check if the
producthasanydefectsonit.Ifso,donot
haveitinstalled.Damagedproductscause
risks for your safety.
C Make sure that the water inlet and
discharge hoses as well as the power
cablearenotfolded,pinchedorcrushed
while pushing the product into its place
after installation or cleaning procedures.

Appropriate installation location

• Placethemachineonarigidfloor.Do
not place it on a long pile rug or similar
surfaces.
• Totalweightofthewashingmachineand
thedryer-withfullload-whentheyare
placed on top of each other reaches to
approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient
load carrying capacity!
• Donotplacetheproductonthepower
cable.
• Donotinstalltheproductatplaceswhere
temperaturemayfallbelow0ºC.
• Placetheproductatleast1cmawayfrom
the edges of other furniture.

Removing packaging reinforcement

Tiltthemachinebackwardstoremove
the packaging reinforcement. Remove the
packagingreinforcementbypullingtheribbon.

Removing the transportation locks

A Donotremovethetransportation
locksbeforetakingoutthepackaging
reinforcement.
A Removethetransportationsafetybolts
beforeoperatingthewashingmachine,
otherwise,theproductwillbedamaged.
1. Loosenalltheboltswithaspanneruntil
theyrotatefreely(C).
2. Removetransportationsafetyboltsby
turning them gently.
3. Attach the plastic covers supplied in the
UserManualbagintotheholesontherear
panel. (P)
C Keepthetransportationsafetyboltsin
a safe place to reuse when the washing
machineneedstobemovedagaininthe
future.
C Nevermovetheproductwithoutthe
transportationsafetyboltsproperlyfixedin
place!

Connecting water supply

C Thewatersupplypressurerequiredtorun
theproductisbetween1to10bars(0.1
–10MPa).Itisnecessarytohave10–80
liters of water flowing from the fully open
tap in one minute to have your machine run
smoothly. Attach a pressure reducing valve
if water pressure is higher.
C Ifyouaregoingtousethedoublewater-
inletproductasasingle(cold)water-inlet
unit, you must install the supplied stopper
tothehotwatervalvebeforeoperatingthe
product. (Applies for the products supplied
withablindstoppergroup.)
C Ifyouwanttousebothwaterinletsofthe
product, connect the hot water hose after
removing the stopper and gasket group
from the hot water valve. (Applies for the
productssuppliedwithablindstopper
group.)
A Models with a single water inlet should not
beconnectedtothehotwatertap.Insuch
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
A Donotuseoldorusedwaterinlethoses
onthenewproduct.Itmaycausestainson
your laundry.
1. Connectthespecialhosessuppliedwith
the product to the water inlets on the
product.Redhose(left)(max.90ºC)isfor
hotwaterinlet,bluehose(right)(max.25
ºC)isforcoldwaterinlet.