Manuals / Bosch Appliances / Household Appliance / Water Heater

Bosch Appliances 2400E LP, 2400E NG manual External condensate drain installation not supplied

Models: 2400E NG 2400E LP

1 48
Download 48 pages 15.27 Kb
Page 13
Image 13

Installation instructions

3.6.3Condensate drain tube requirements

Exhaust collar condensate drain installation (supplied with heater)

BThe condensate drain tube kit must be used for all installation types. Failure to properly install condensate drain will void the warranty.

BWhen installing the condensate drain tube kit on the exhaust collar (see diagram below), be sure to form a trap by means of a 3" (76.2 mm) loop partially filled with water. This loop must be as low as possible to allow proper drainage of condensate. The supplied tube is 3/8" ID high temperature silicone and must be attached to the condensate port on the exhaust collar with its supplied gear clamp (first remove brass screw from port).

BTo increase tube length, connect vinyl tubing (not supplied with heater) to the supplied tube. Do not reduce tubing diameter when using connector or additional tubing.

BThe condensate must be disposed of according to local regulations.

Condensate port on exhaust collar

1.Remove brass hex head screw

2. Fit tube with gear clamp

3.Loop size and location. Coil tube into 3” loop with nylon tie (don't crimp tubing) and fill bottom of loop with water

Fig. 12 Exhaust collar condensate drain installation

Note: No part of supplied silicone tube should be installed above condensate tapping or improper drain- age may occur. (see Fig. 12).

External condensate drain installation (not supplied)

An additional external condensate drain must be installed under the following conditions:

•Vertical terminating vent installations

•Horizontal terminating vent installations where the total vent length is greater than 5 feet

•Vent installation where any section of the exhaust vent pipe passes through an unconditioned space.

Note: Condensate must be disposed of according to local codes.

Note: Do not install condensate drain in areas where it may freeze.

1.Install condensate drain as close to heater as possible.

2.Use 3/8" ID high temperature silicone tubing to connect to condensate drain port. Do not use copper piping for any portion of the condensate drain.

3.Form a condensate trap by means of a 3" loop and fill bottom of loop with water.

4.To increase the tube length, connect to end of the high temperature silicone tubing with vinyl tubing, PVC or CPVC pipe. Do not reduce the internal diameter at any point.

5.Dispose of condensate according to local codes.

Fig. 13 Required condensate drain installation (Combustion air piping not shown)

3.6.4Room sealed installation (Twin pipe)

Warning: In areas where outdoor temperatures commonly fall below 36°F, a twin pipe venting system is required. Failure to do so may result in cold outside air being drawn across the heat exchanger causing it to freeze and burst. This failure is not covered under the manufacturer's warranty.

BAlthough it is permitted to draw combustion air from inside the structure in warm climates, the recom- mended method is to provide combustion air through

6 720 608 263

13

Page 12 Page 14
Page 13
Image 13
Bosch Appliances 2400E LP manual External condensate drain installation not supplied, Room sealed installation Twin pipe
Page 12 Page 14

2400E NG, 2400E LP specifications

Bosch Appliances has long been synonymous with quality and innovation in the kitchen appliance sector. Among their impressive lineup, the Bosch 2400E LP (Liquid Propane) and 2400E NG (Natural Gas) models stand out as prime examples of the brand’s commitment to performance and functionality.

Both the 2400E LP and 2400E NG are designed with user convenience and culinary excellence in mind. One of the most notable features of these appliances is their exceptional heat distribution, which ensures that food cooks evenly. This is particularly beneficial for grilling, where inconsistent heat can lead to unevenly cooked meals. The burners are crafted to provide high-efficiency performance while consuming less fuel, making them an economical choice for both home cooks and culinary enthusiasts.

Each model boasts a sleek, modern design that can seamlessly integrate into various kitchen styles. The stainless steel construction not only enhances aesthetics but also increases durability, ensuring the appliance can withstand the rigors of daily use while maintaining its appearance. The 2400E series also features a compact size, making it suitable for kitchens of all dimensions, including those with space constraints.

In addition to design and performance, safety features are a priority for Bosch. The 2400E models come equipped with sturdy flame control knobs, allowing users to adjust heat settings with precision, reducing the risk of accidental flare-ups. Moreover, the integrated ignition system is designed for reliability, ensuring that starting the unit is hassle-free.

Versatility is another hallmark of the Bosch 2400E LP and NG models. These appliances are compatible with a range of cooking accessories, from griddles to rotisserie attachments, providing multiple cooking methods to satisfy diverse culinary endeavors. The grease management system is another highlight, simplifying cleanup and maintenance after cooking sessions.

Another innovative technology in the Bosch 2400E series is the Smart Grilling feature, which includes temperature sensors that provide real-time feedback. This allows users to monitor cooking progress effortlessly, enhancing the overall cooking experience. The models also include a robust warranty, ensuring peace of mind for consumers.

In conclusion, Bosch Appliances’ 2400E LP and NG models represent a fine balance of innovation, safety, and style. With their powerful cooking capabilities, thoughtful design features, and user-friendly technologies, they stand as excellent choices for anyone looking to elevate their cooking experience.