Bosch Appliances F.01U.252.722 3 Installation

NurseCall Relay Unit Installation | en 13

Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12

3 Installation

3.1 Unpacking

The NurseCall Relay Unit is carefully packed for transportation.

The components contained in the box are protected, but should be handled with care.

Store the packaging material for further use (storage or transport).

1. Take all components out of the box and place the NurseCall Relay Unit on the working

space.

2. Check each component in the box, in accordance with the list of contents below.

3. Check that the NurseCall Relay Unit and its accessories have not been damaged during

transportation.

In case of defective or missing equipment, do not try to install the NurseCall Relay Unit.

Contact immediately your local representative.

3.1.1 List of contents

Description

NurseCall Relay Unit

Power supply adaptor (Europe)

230VAC/10VAC

or

Power supply adaptor (UK)

230VAC/10VAC UK

or

Power supply adaptor (US)

115VAC/10VAC

Antenna 434MHz 1/2 L=34 cm FME

Straight adapter BFME-TNC

Right angled bended adapter BFME-ETNC

2 m Cable FCC 6/4

NurseCall Relay Unit User Manual

Contents

Main Page Table of Contents Page 1 Safety instructions 1.1 Importance of safety instructions 1.4 General safety instructions 1.2 Disregarding safety rules 1.3 Environmental conditions 1.4.1 Observation and information 2 Description 2.1 General description 2.1.1 Top view Page 2.1.3 Front view 2.1.4 Relay Unit rear view 2.1.5 Relay Plus Unit rear view 1 2 12 3 2.2 Detailed description 2.2.1 Loudspeaker OFF ON C OK Page 2.2.4 RS-485 interface 2.2.5 Antenna 3 Installation 3.1 Unpacking 3.1.1 List of contents 3.2 Installation 3.2.1 Generalities 3.2.2 Installation on a piece of furniture 3.2.3 Wall installation 3.2.4 Installing the antenna 3.2.5 Connecting to the mains 3.2.6 Setting the jumpers on the communication board on the Relay Plus Unit 3.2.7 Connecting the RS-485 3.2.8 Connecting the RS-232 to the Relay Plus Unit 3.2.9 Setting the 100 Ohm termination jumper 4 Programming 4.1 Generalities DATE: 03.01.12 TIME: 12:12:31 A 4.2 First use 4.2.1 List of original factory settings 4.2.2 Parameters set by the NurseCall Main Unit 4.2.3 Locating mode and identification number LOCATING ? (OFF/ON ) 4.3 Special settings 4.4 Printer/display setup on the Relay Plus Unit Page 4.4.5 Selection "DISPLAY NORSK" 5 Operation 5.1 Adjusting the loudspeaker volume 5.2 Consulting the alarm or event buffer 5.2.1 Switching between alarm and event buffers indication 5.2.2 Display indications Page 6 Maintenance 6.1 Checking the system 6.2 Monitoring the power supply 6.3 Monitoring the backup battery 6.4 Cleaning 6.5 Parts replacement 6.5.2 Backup battery replacing 7 Disposal 7.1 Disassembly 7.2 Returning to the manufacturer 7.3 Materials 7.4 Battery A Appendix A.4 List of criteria A.5 Connectors A.5.1 LINE socket (unit bottom) A.5.4 RS-485 socket (unit rear) A.5.2 Power socket (unit bottom) A.5.3 RS-232 socket (Relay Plus Unit rear)