Manuals / Brands / Personal Care / Home Care Product / Bosch Appliances / Personal Care / Home Care Product

Bosch Appliances F.01U.252.722 4.4 Printer/display setup on the Relay Plus Unit

1 36

Download 36 pages, 1.57 Mb

22 en | Programming NurseCall Relay Unit

F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems

4.3.4 Assistance and fire non priority

This command sets the assistance call and the fire alarm as non-priority calls. This means that

the last alarm is displayed, whatever its type. This is the default value.

1. Type the code 123992. The unit plays a melody and a confirmation message is displayed.

4.3.5 Special texts in German

This command sets special texts in German. The displayed criteria are:

– BAD/WC instead of TECHNIK

– HILFE-2 instead of NOTRUF2

1. Type the code 123007. The unit plays a melody and a confirmation message is displayed.

4.3.6 Standard texts in German

This command sets standard texts in German. This is the default value.

1. Type the code 123008. The unit plays a melody and a confirmation message is displayed.

4.4 Printer/display setup on the Relay Plus Unit

4.4.1 Access to the printer/display setup menu

1. Press then to access the programming menu.

2. Press to enter the RS-232 output menu or to check the RS-232 output setup.

3. Press to enter the printer/display setup. Press to escape.

4. Scroll with and to select one of the following:

–None

–Printer

–DISPLAY ZETTLER

–DISPLAY NORSK

ASSISTANCE & FIRE

NONPRIORITY

MULTITONE TEXTE

BAD/WC + HILFE-2

STANDARDTEXTE

TECHNIK + NOTRUF2

NOTICE!

The printer/display setup can only be configured on a NurseCall Relay Plus Unit connected to

a NurseCall system via the RS-485 bus.

¬ OK:Program

¤:Info

¬ Parameter Nr. 00

RS-232 Output £

Contents

Main Page Table of Contents Page 1 Safety instructions 1.1 Importance of safety instructions 1.4 General safety instructions 1.2 Disregarding safety rules 1.3 Environmental conditions 1.4.1 Observation and information 2 Description 2.1 General description 2.1.1 Top view Page 2.1.3 Front view 2.1.4 Relay Unit rear view 2.1.5 Relay Plus Unit rear view 1 2 12 3 2.2 Detailed description 2.2.1 Loudspeaker OFF ON C OK Page 2.2.4 RS-485 interface 2.2.5 Antenna 3 Installation 3.1 Unpacking 3.1.1 List of contents 3.2 Installation 3.2.1 Generalities 3.2.2 Installation on a piece of furniture 3.2.3 Wall installation 3.2.4 Installing the antenna 3.2.5 Connecting to the mains 3.2.6 Setting the jumpers on the communication board on the Relay Plus Unit 3.2.7 Connecting the RS-485 3.2.8 Connecting the RS-232 to the Relay Plus Unit 3.2.9 Setting the 100 Ohm termination jumper 4 Programming 4.1 Generalities DATE: 03.01.12 TIME: 12:12:31 A 4.2 First use 4.2.1 List of original factory settings 4.2.2 Parameters set by the NurseCall Main Unit 4.2.3 Locating mode and identification number LOCATING ? (OFF/ON ) 4.3 Special settings 4.4 Printer/display setup on the Relay Plus Unit Page 4.4.5 Selection "DISPLAY NORSK" 5 Operation 5.1 Adjusting the loudspeaker volume 5.2 Consulting the alarm or event buffer 5.2.1 Switching between alarm and event buffers indication 5.2.2 Display indications Page 6 Maintenance 6.1 Checking the system 6.2 Monitoring the power supply 6.3 Monitoring the backup battery 6.4 Cleaning 6.5 Parts replacement 6.5.2 Backup battery replacing 7 Disposal 7.1 Disassembly 7.2 Returning to the manufacturer 7.3 Materials 7.4 Battery A Appendix A.4 List of criteria A.5 Connectors A.5.1 LINE socket (unit bottom) A.5.4 RS-485 socket (unit rear) A.5.2 Power socket (unit bottom) A.5.3 RS-232 socket (Relay Plus Unit rear)