Note: It is best to carry out a trial cut.
The cutting mark 0° ( 16) indicates the position of the saw blade for right-angled cuts.

2 610 392 415 - Buch Seite 3 Dienstag, 10. Dezember 2002 7:52 07

 

 

 

.

 

 

o

Before Putting into Operation

 

.

 

 

r

 

 

 

.

 

 

Before any work on the machine itself, pull

the mains plug.

s

 

 

 

 

 

Riving Knife

Checkingprahathe Adjustment of the

For safety reasons t e riving knife 8 must always be used. The iving knife avoids seizing of the saw blade while sawing.

The adjustment takes place at the maximum cut- mikosoftting dep h.

L sen the screw 6, adjust the riving knife 8 and retighten the screw.

6

8

2,5 - 5 mm

2,5 - 5 mm

 

 

 

 

 

 

.

Adjusting the Cutting Angle

 

 

o

 

 

 

 

.

 

 

 

 

r

 

 

 

 

 

.

 

 

Before any work on the machine itself, pull

 

 

 

the mains plug.

 

 

s

 

 

 

 

 

 

 

 

 

Loosen winged screw(s) 5.

praha

 

 

 

 

 

 

 

 

 

Swing the machine to the side until the desired

 

 

 

cutting angle is set on the scale 13.

 

 

 

 

 

Tighten winged screw(s) 5 again.

 

 

 

 

 

Note: For mitre cutting, the cutting depth is

 

 

 

smaller than the value shown on the cutting depth

 

 

 

scale 17.

 

 

 

 

 

 

mikosoft

 

 

 

 

 

 

Cutting Marks

 

 

 

 

 

 

45° 0°

 

45° 0°

 

 

 

Adjusting the Cutting Depth (see figure C )

Before any work on the machine itself, pull

The cutting mark 45° ( 15) indicates the position

of the saw blade for 45° cuts.

the mains plug.

 

To achieve an optimum cut, the saw blade

For an exactly true cut, apply the saw as shown

must not protrude more than 3 mm at the

in the diagrams.

most from the material.

 

 

For adjusting the cutting depth, loosen the

 

 

 

 

 

 

 

 

 

 

 

 

 

winged screw/clamping lever (PKS 46) 18 and

 

Initial Operation

 

 

 

 

.

 

 

raise the saw from, or lower it to the base plate 7:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Raise

 

 

 

.

 

Observe correct mains voltage: The voltage of

 

 

 

for smaller cutting depths

 

 

 

 

 

 

 

the power source must agree with the voltage

 

 

 

 

 

Lower

 

 

o

 

o

 

 

 

 

 

specified on the

 

 

 

 

 

 

for greater cutting.depths

 

nameplate of the machine .

 

 

 

 

 

 

 

r

 

 

 

 

 

 

 

r

 

 

 

 

 

Set the desired depth on .the cutting depth

 

Equipment marked with 230 V can also be con-

 

 

 

 

 

 

nected to 220 V.

 

 

.

 

 

 

 

 

scale 17.

 

 

s

 

 

 

 

s

 

 

 

 

 

Tighten winged screw/cl

 

 

 

 

 

 

 

 

 

 

 

 

mping lever 18 again.

 

Switching On and Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For starting operation of the mac ine, actuate

 

 

 

 

 

Clamping Lever (PKS 46)

 

 

 

 

 

 

the safety switch against starting 1 first, and then

 

 

 

 

 

The clam

ing

ower of the clamping lever 18 can

 

press and hold the On/Off switch 2 afterwards.

 

 

 

 

 

 

To switch off the machine, release the On/Off

 

 

 

 

 

be adjusted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

praha

 

 

 

 

 

 

 

 

praha

 

 

 

switch 2.

 

 

 

 

 

 

 

 

To do his, unscrew the clamping lever and set it

 

 

For safety reasons the On /Off switch of

 

 

 

 

 

at at least 30° counter-clockwise, screw on again.

 

 

 

 

 

mikosoft13 • 2 610 392 415 • TMS • 28.11.02

 

 

 

 

the machine cannot be locked; it must

 

 

 

 

 

 

 

 

 

 

 

 

 

 

remain pre

ed during the entire opera-

 

 

 

 

 

 

 

tion.

 

 

 

 

 

 

 

 

 

 

mikosoft

 

 

 

 

 

 

 

English - 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 13
Image 13
Bosch Power Tools PKS 46, PKS 40 operating instructions Before Putting into Operation