CONNECTING THE PROJECTOR
CONNECTING THE COMPUTER
CONNECTING TO THE COMPUTER INPUT TERMINALS (1 and 2)
Personal computers can be connected to the
●Connect the computer to these terminals using the VGA cable and VGA/Macintosh adapter (provided).
CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.
CONNECTING TO THE MONITOR OUTPUT TERMINAL
This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source is selected, this terminal outputs Computer 1 input information.
An external monitor can be connected to the
●Connect the monitor to this terminal using the VGA cable (not provided).
HDB
5 | 4 | 3 |
| 2 | 1 |
10 |
| 9 | 8 | 7 | 6 |
15 14 13 12 11
Pin No./Signal | Pin No./Signal | ||
1 | Red input | 9 | Non Connect |
2 | Green input | 10 | Ground (Vert. sync.) |
3 | Blue input | 11 | Sense 0 |
4 | Sense 2 | 12 | Sense 1 |
5 | Ground (Horiz.sync.) | 13 | Horiz. sync |
6 | Ground (Red) | 14 | Vert. sync |
7 | Ground (Green) | 15 | Reserved |
8 | Ground (Blue) |
|
|
CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)
●Connect audio outputs from your computer to these jacks using the audio cable (not provided).
CONNECTING TO THE CONTROL PORT (DIN 8 PIN) CONNECTORS (1 and 2)
●If you wish to control the computer with projector's remote control unit, you must connect control port (PS/2, Serial or ADB port) on your computer to projector's control port with cable. (three type cables supplied; for PS/2 Port, Serial Port and ADB Port).
■CONTROL PORT
8 | 7 |
|
|
|
|
|
|
|
|
|
|
| 6 |
|
| PS/2 Port | Serial Port | ADB Port |
|
|
|
|
|
|
|
|
|
|
|
| 1 | RXD | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 | CLK | ADB | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | DATA | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | GND | GND | GND |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 | RTS/CTS | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 | TXD | ||
5 | 2 |
| 1 | 4 | 3 | 7 | GND | GND | ||||||||||
| 8 | GND | GND | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
NOTE: The RXD port (1 pin on the Serial Port) is provided on control port 2 connector only. If you control the projector by computer, you must connect control port 2 connector.
11
