Terreon® 54" Semi-circular Washfountain with Cylindrical Air Valve

 

TDB3104, WF3204

Installation Instructions

Thermostatic Mixing Valve Troubleshooting

NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the fol- lowing conditions:

If stop/check valves are used, make sure that they are fully open.

Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross- connections or leaking stop/check valves.

Check the hot water heater output to make sure that it is at least 20° F above the set tempera- ture.

Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the valves after inspection and repair is complete.

Problem: Limited water flow

Cause: Dirt and debris have built up in the valve or strainer.

1.Remove and clean strainer (see Figure 14 or 15 on page 29). If strainer needs to be replaced, order Bradley part no. 173-028.

2.Check the piston for smooth movement.

To check the valve's piston for free and smooth movement, follow the procedures outlined below:

1.Remove the valve's cap and thermostat (see Figure 14 on Page 29).

2.Push down on the piston with your finger (the piston should move freely). If the movement is not as it should be, the piston needs to be cleaned. Follow the method outlined below for clean- ing the piston and valve body:

Remove the thermostat.

Lift the piston out with a needle-nose pliers and remove the spring.

Any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable cleaner is not sufficient to remove debris, a 400-grit sandpaper may be used to polish and hone the pis- ton and valve body).

Snap spring into piston (will detent) and reassemble into the valve body. Retest the piston.

3.If, after a thorough cleaning, the piston does not move freely, the piston must be replaced. Contact your Bradley representative and ask for Repair Kit (part number S65-259).

Problem: External leaks in the system

Cause: O-rings have been damaged.

Solution: Replace O-rings where necessary. For replacement of the O-rings, contact your Bradley representative and ask for Repair Kit (part number S65-259).

Problem: Improper water temperature or temperature fluctuation

Cause: Thermostat is slowly failing or not working at all.

Solution: Check the thermostat for proper operation.

1.At room temperature (80° F or less) remove cap and thermostat.

2.Place thermostat into container with 115° F water. The pushrod should pop out of the thermostat approximately 1/10".

3.If thermostat pushrod does not pop out, the thermostat must be replaced. Contact your Bradley representative and ask for Repair Kit (part number S65-259).

Cause: Valve temperature is not properly set.

Solution: Adjust the temperature. Using a blade screwdriver, turn the adjustment stem counterclock- wise to increase the temperature or clockwise to decrease the temperature.

28

2/8/07

Bradley Corporation • 215-1470 Rev. H; EN 06-915

Page 28
Image 28
Bradley Smoker WF3204, TDB3104 Thermostatic Mixing Valve Troubleshooting, Problem Limited water flow

TDB3104, WF3204 specifications

The Bradley Smoker WF3204 and TDB3104 are two exceptional units designed for both amateur and professional smokers who seek to elevate their culinary experience with a blend of traditional techniques and modern technology. These electric smokers are celebrated for their consistency, ease of use, and innovative features that cater to various smoking needs.

The Bradley Smoker WF3204 is a versatile smoker that accommodates a range of smoking styles from cold to hot smoking. One of its standout features is the dual heating element, which allows for precise temperature control during the smoking process. This technology enables users to maintain optimal smoking temperatures, ensuring that meats, cheeses, and vegetables are infused with the desired smoky flavor.

Additionally, the WF3204 boasts a built-in smoke generator that uses Bradley's signature wood bisquettes. These bisquettes are designed to burn for a precise 20 minutes, delivering consistent smoke flavor without the risk of bitterness that can arise from traditional wood chips. The smoker's automatic feed system ensures that each bisquette is perfectly placed, minimizing user intervention and allowing for a hands-free smoking experience.

Similarly, the TDB3104 model offers a user-friendly smoking experience with an emphasis on efficiency. Its digital control panel makes it incredibly simple to set smoking times and temperatures, enabling even novice smokers to achieve professional results. The TDB3104 also features a spacious smoking chamber, which can accommodate a variety of foods, making it ideal for larger gatherings or meal prep.

Both models come equipped with a durable and insulated construction that enhances heat retention, allowing for energy-efficient operation. The stainless-steel exterior not only provides a sleek, modern look but also ensures durability against the elements. Furthermore, the internal racks are adjustable, giving users the flexibility to smoke larger cuts of meat or multiple items simultaneously.

An important characteristic of both the WF3204 and TDB3104 is their portability. Each model is designed with ease of transport in mind, making them suitable for backyard barbecues, tailgating, or camping trips.

In conclusion, Bradley Smokers WF3204 and TDB3104 stand out in the smoking appliance market due to their innovative features, user-friendly designs, and robust construction. Whether you are an experienced pitmaster or a beginner looking to explore the world of smoking, these models promise exceptional flavor and smoking results that will impress family and friends alike.