WALL ANCHORS LOCATION

13. INSTALL THE HOOD

CAUTION

 

Hold the hood until it is completely secured to the wood

 

mounting strip.

 

INTERNAL BLOWER(S) ONLY

MOUNTING SCREWS LOCATION

 

Run power cable to installation location. Remove the electrical compartment cover.

 

Insert the cable in the hood and tighten the wire clamp to secure the cable.

 

ALL INSTALLATIONS

HD0264

 

Rest the back cavity of the hood on the wood mounting strip.

Secure the hood to wood mounting strip with (4) screws no. 8 x 3/4’’ (for 30’’ and

36’’ width hoods) or (6) screws (for 42’’ and 48’’ width hoods) provided at locations shown. Drill (3) 3/16’’ size holes into the drywall for wall anchors through the existing holes in the inside hood back in the locations shown. Then, install the three wall anchors with the remaining no. 8 x 3/4’’ screws and the (3) washers provided.

For a non-ducted installation, go to step 15, Connect the wiring.

14.ROUGH-IN PLATE LOCATION (EXTERNAL BLOWERS HOODS ONLY)

Run power cable to installation location. For ducting through top of hood, existing plate remains in place on inside back of hood.

For ducting through back of hood, remove existing plate from inside back of hood and remove the rough-in plate from the top of hood. Attach the plate to inside top of hood to cover hole. Secure to threaded studs with same (4) nuts. Install the rough-in plate to the back of hood so that the wiring box is located on the right side as you are facing the hood.

Connect ducting to rough-in plate as you are installing the rough-in plate. Use duct tape to make all joints secure and air-tight.

ROUGH-IN PLATE

ON TOP OF HOOD

WIRING

LOCKNUTS

COVER

LOCKNUTS

HD0262 PLATE ON BACK OF HOOD

15. CONNECT THE WIRING (ALL BLOWERS)

!WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally.

Remove wiring cover from rough-in plate or electrical compartment and set aside.

INTERNAL BLOWERS: Connect cable into wiring box using wire connectors. Connect BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw.

CAUTION

The ORANGE wire (A) is for make-up air device connection only. If there is no make-up air device, never remove the cap on the ORANGE wire end.

Reinstall wiring cover.

IN-LINE OR EXTERIOR BLOWERS: See instructions included with blower.

A

HE0088

- 11 -

Page 11
Image 11
Broan E6030SS Install the Hood, Connect the Wiring ALL Blowers, ROUGH-IN Plate Location External Blowers Hoods only

E6030SS, E6036SS specifications

The Broan E6036SS and E6030SS range hoods are among the standout products in the Ventilation category, notable for their sleek design and robust performance. Both models boast a contemporary stainless steel finish, lending a modern aesthetic to any kitchen while ensuring durability and longevity.

With widths of 36 inches and 30 inches respectively, these range hoods are designed to effectively cover a wide cooking surface, regardless of the size of your stovetop. The powerful motor is capable of delivering high CFM (Cubic Feet per Minute) airflow, which ensures that smoke, steam, and odors are quickly and efficiently expelled. This powerful ventilation system is crucial for maintaining air quality, especially in busy kitchens.

One of the main features of the Broan E6036SS and E6030SS is their easy-to-operate controls. These models typically come with three-speed settings, allowing users to adjust the airflow according to their cooking needs. The intuitive controls make it easy to switch between different speeds, ensuring optimal ventilation without excess noise. Speaking of noise, these range hoods are engineered for quiet operation, even at high speeds, making them an excellent choice for open-concept living spaces.

Another noteworthy characteristic of both models is their lighting features. They come equipped with bright, energy-efficient LED lights that illuminate the cooking area, enhancing visibility while preparing meals. The integrated lighting not only makes cooking more enjoyable but also adds to the overall aesthetic of the kitchen.

Installation is made simple with a versatile design that accommodates both ducted and ductless configurations. Ductless installations can utilize optional charcoal filters, which help to recirculate the air while eliminating odors and particulates.

In terms of maintenance, the Broan E6036SS and E6030SS feature dishwasher-safe filters that are easy to remove and clean. This is a significant convenience for users looking to maintain optimal performance without hassle.

Overall, the Broan E6036SS and E6030SS range hoods represent a blend of style, efficiency, and practicality. Their powerful performance, user-friendly features, and modern design ensure they are an excellent addition to any kitchen, making them popular choices among homeowners and cooks alike. Whether you are a culinary enthusiast or someone who simply enjoys cooking, these range hoods elevate the kitchen experience by ensuring a clean and inviting environment.