Broan QP130SSC, QP130WW warranty Contents, Operation, Cleaning & Maintenance, Prepare Hood Location

MODELS QP130BL • QP130BLC • QP130SS • QP130SSC QP130WW • QP130WWC • QP136BL • QP136SS • QP136WW

CONTENTS

INCLUDED WITH THE HOOD:

(1) 3¼” X 10”

DAMPER / DUCT CONNECTOR

(2)

GREASE

FILTERS

(1) 7” ROUND

DUCT CONNECTOR

(1) PARTS BAG CONTAINING:

Page 2

OPERATION

Always turn the hood ON before cooking in order to establish an air flow in the kitchen. After turning off the range, let the hood run for a few minutes to clear the air.

Operate the hood as follows:

0 1 2 0 1 2

BLOWER SWITCH

This 3-position rocker switch turns blower ON and OFF and controls blower speed.

Left rocker position (0) turns blower OFF.

Center rocker position (1) turns blower ON to low speed. Right rocker position (2) turns blower ON to high speed.

(3)

WIRE NUTS

(9)

#8 X 1/4”

DUCT CONNECTOR

SCREWS

(1) BULB

SUCTION

CUP TOOL

(5)

#10 X 5/8”

RD. HD.

MOUNTING

SCREWS

LIGHT SWITCH

This 3-position rocker switch turns lights ON and OFF and controls their intensity.

Left rocker position (0) turns lights OFF.

Center rocker position (1) turns lights ON to low intensity. Right rocker position (2) turns lights ON to high intensity.

NOTE:

This hood utilizes an offset blower design to achieve greater performance and lower sound levels. As a result, you may notice that cooking impurities are more attracted to one side or appear to be pulled-in faster than they appear on the opposite side. This is completely normal. The hood has been designed and tested to provide good capture of cooking impurities and odors under all

CLEANING & MAINTENANCE

For performance, appearance, and health reasons, clean filter, fan and grease-laden surfaces. Use only a clean cloth and mild detergent solution on stainless and painted surfaces.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergents, or as a result of local water conditions - but this will not affect filter performance. This discoloration is not covered by the warranty.

Clean the non-duct recirculating filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dishwasher. The special “Clean Sense” feature

normal cooking conditions regardless of the cooking location on the cooktop. Please note that cooking on the rear burners will always result in the best capture results, regardless of the hood design.

PREPARE HOOD LOCATION

ROOF CAP	3¼" X 10" or
	7" ROUND DUCT
	(For vertical
	discharge)

indicates when the filter is to be replaced. The blue and yellow strips will blend to green when it is time to change the filter. The “Clean Sense” feature works best when facing toward the cook- ing surface. Change the non-duct recirculating filters every 6 months. For replacement non-duct recirculating filters - purchase S99010353 or Model BPPF30 for 30” hoods, or S99010354 or Model BPPF36 for 36” hoods.

The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor with the exact service motor. The impeller should also be replaced.

SOFFIT

CABINET

HOOD

24" - 30" ABOVE

COOKING SURFACE

HOUSE WIRING (Top or Back of hood)

WALL CAP

3¼" X 10" DUCT

(For horizontal discharge)

Use 120 V, 35 W, shielded halogen bulbs - MR16 with GU10 base. Purchase bulbs separately.

1	Determine whether hood will discharge vertically (3¼”
	x 10” or 7” Round), or horizontally (3¼” x 10” only). For
	vertical or horizontal discharge, run ductwork between
	the hood location and a roof cap or wall cap. For best
	results, use a minimum number of transitons and elbows.