Manuals / Brands / Household Appliance / Sewing Machine / Brother / Household Appliance / Sewing Machine

Brother BES-941BC Loading and Loading of Floppy Disk, Registration of Sewing Data into Machine Memory

1 182

Download 182 pages, 2.21 Mb

BES-941BC • BES-1241BC

Chapter 3 Selection of Data and Embroidering

• Other data

Data format Icon

Barudan FDR

Barudan FMC

Zanks ZSK

(These icons are displayed in the lower right of the screen.)

Loading and Loading of Floppy Disk

1. When loading a floppy disk, set it straight with the labeled surface facing

this side.

2. When unloading a floppy disk, press the eject switch.

3. When it comes out, pull it straight.

When the access lamp if ON, never press the eject switch. Otherwise, embroidery data in the

floppy disk may be destroyed.

Registration of Sewing Data into Machine Memory

1. Load a floppy disk with sewing data.

Access lamp

Eject switch

Contents

Main Page SAFETY INSTRUCTIONS Indications Symbols 2 Notes on safety Environmental requirements Installation Sewing Cleaning Maintenance and inspection 3 Warning labels 1 CAUTION 2 PELIGRO 3 Page Before Starting Operation Protecting data in floppy disks Procedure of Reading This Manual Explanation of models Configuration of this manual Page Screen Composition Initial Screen Page Contents Chapter 1 Preparation of Embroidery Machine Chapter 2 Embroidering Procedures Chapter 3 Selection of Data and Embroidering Chapter 4 Editing of Embroidering Data Chapter 5 Setting Chapter 6 Operation of Machine Page Page Page 1. Specifications 2. Names of Machine Components BES-941BC The machine heads are numbered 1 to 4 from the right front. BES-1241BC Accessories a a 3. Installation When using a fork lift 3-1 Transportation of Machine When relocating the machine, push the steel frame. Page 3-2 Installation of Machine 3-3 Preparation of Needle Bar Case Page 3-4 Mounting of Table Page Page Page 3-5 Mounting of Cotton Stand Page 3-6 Lubrication to Needle Bar Case Page 4. Preparation for Embroidering 4-1 Upper Threading Page Page 4-2 Replacement of Bobbin 4-3 Replacing and Selecting Needle 4-4 Attachment of Embroidery Hoop and Frame Page Page Page Page Page Page 4-6 Adjustment of Thread Tension Adjustment of upper thread 1. The tension spring should be adjusted to 6~8 mm in height and 0.07~0.12 N (7~12 gf) in force. * Correct adjustment Adjustment of tension spring Page Page Page Functions of Operation Panel Operation Panel 0 12 45 3 6 7 8 9 Page Operation panel Switches at Machine Heads Switches on Tension Plate Page Flowchart of Preparation for Embroidering Turn on the Machine Power Retrieve the Embroidery Data Start Embroidering Page Page Selection of Embroidery Data Embroidering Operation Selection of Data Registration of Embroidery Data from Floppy Disk Loading and Loading of Floppy Disk Registration of Sewing Data into Machine Memory Page Reading from Memory Registration of Embroidery Data from BE-100 Deletion of Embroidery Data from Machine Memory When deleting embroidery data in the machine memory entirely: Modification of Embroidery Data Name J K L 1. Press . P Q R S . When modifying embroidery data names entirely When modifying only one character: Page Sewing Operation Before Starting Sewing HOOP FLAT CAP Starting Sewing Operation Feedhold and Cancellation of Sewing Feedhold Cancellation Step Forward and Step-Back Step Forward/Step-Back Mode Setting Amount or Timing of Step Forward/Step-Back When the number of stitches is specified, the needle steps forward (back) to an input position: Page Writing the embroidering data Page Editing Rotation Enlargement and Reduction Enlargement/reduction at the same ratio in the X/Y directions Enlargement/reduction at different ratios in the X/Y directions Mirror Right/Left Mirror Pattern Up/Down Mirror Pattern Zero Point-Symmetric Mirror Pattern Repetition Page Other Editing 0 Stitch Deletion Thread Trimming Feed Number Swing Width Correction Page Page Setting of Needle Bars Setting of Thread Breakage Sensor Setting of Machine Setting of Environment Page Setting of Needle Bars Insertion of Feedhold Insertion of Hoop Retract Thread Breakage Sensor Setting of sensor validity/invalidity Thread Breakage Sensitivity Automatic Step-Back Setting of Lower Thread Counter/Stitch Counter Setting of Machine Embroidery Hoop Speed Range Speed of Each Speed Range Setting of Mending Page Thread Trimming Length Thread Withdrawal Feed Length Inching Sewing Area Registration of Sewing Start Position Hoop Retract Point Cancellation of Setting Hoop Automatic Retract Movement to Registered Sewing Start Point Setting of Environment Return to Start Point Speed Range Checking the Embroidery Area Power Voltage Setting of RS-232C Communication Speed Display Language Alarm Sound Motive Speed Release B1 error Boring Validation/Invalidation of Boring Mode Validation/Invalidation of Data Shift Lock Stitch Setting lock stitch at the sewing start position Setting the lock stitch on the sewing send position Setting the lock stitch at the sewing start position after thread trimming Speed Limit in a Short Pitch Invalidating speed limit in a short pitch Feed Timing Display of Information Pattern Information Features of Machine Information about Versions Page 1. Operating Procedures 1-1 Power Source 1-2 Preparation for Embroidering 2. Machine Stop 2-1. Stopping the Machine 2-2. Resetting Machine Stop 2-3. Emergency Stop of the Machine 2-4. Resetting Emergency Stop 3. Measures against Thread Breakage 3-1 Remedies STOP 3-2 Mending Page 4. Jog Embroidering 5. Hoop Feed Position 6. Area Check 6-1 External Tracing 6-2 Automatic Hoop Movement in Area Page 7-2 Inching Mode during Embroidering (Forcible Hoop Movement) END 8. Detection of Zero Point Page Page 1. Cleaning Rotary Hook 2. Oiling 2-1 Head Page 3. Greasing 3-1 Head Page Page Page 3-2 Feed Guide Section 3-3. Lower shaft module Page Page Page 1. Adjusting Needle Bar Height Page When using the bottom dead center gauge Page 2. Replacing (Attaching) Rotary Hook 3. Adjustment of Clearance Between Needle and Rotary Hook 4. Adjustment of Timing Between Needle and Rotary Hook 5. Adjustment of Presser Foot Height 6. Adjustment of Thread Trimmer 6-1 Attaching the Fixed Knife 6-2 Checking the Movable Knife Position Page 7. Adjusting the Belt Tension Page BES-941BC BES-1241BC BES-941BC BES-1241BC 161 BES-941BC BES-1241BC BES-941BC BES-1241BC 163 Page Page Mechanical Section Problem Check Point Check these points once again Problem Check Point Check these points once again Electrical Section Page Page Page Page Page Page Page Page Page Attaching Bobbin Winder