Brother NV6000D Crazy Quilting, Smocking Stitches

SEWING THE STITCHES

116

Crazy Quilting

For a decorative look called “Crazy Quilting”, the

following stitches can be sewn on top of a pressed

seam allowance.

aSelect a straight stitch and attach presser

foot “J”.

bWith the right sides facing each other, sew

two pieces of fabric toget her, and then

press open the seam allowance.

aStraight stitch

bSeam margins

c6.5 mm (approx. 1/4 inch)

dWrong side

cSelect a stitch for top stitching.

dPlace the fabric right side up in the

machine, and center the presser foot over

the seam when sewing.

aRight side of fabric

Smocking Stitches

Use smocking stitches for decorative sewing on

clothes, etc.

aSelect a straight stitch and attach presser

foot “J”.

bSet the stitch length to 4.0 mm (approx.

3/16 inch) and loosen the upper thread

tension to approximately 2.0 (see “Setting

the Stitch Length” on page 67 and “Setting

the Thread Tension” on page 67).

cPull the bobbin and upper threads out by

50 mm (approx. 1-15/16 inches).

dSew the seams, leaving approximately

10 mm (approx. 3/8 inch) between the

seams, then trim excess thread, leaving

50 mm (approx. 1-15/16 inches).

aApproximately 10 mm (approx. 3/8 inch )

ePull the bobbin threads to obtain the

desired amount of gather, and then smooth

the gathers by ironing them.

fSelect or .

Memo

• For details on each stitch, refer to the

“STITCH SETTING CHART” at the end of

this manual.

Contents

Main Computerized Embroidery and Sewing Machine X1_BrotherE_OM_cover C M Y K Operation Manual Operation Manual Trademarks IMPORTANT: Intel License Agreement For Open Source Computer Vision Library i INTRODUCTION DANGER 1 WARNING 2 3 5 6 SAVE THESE INSTRUCTIONS 7 8 Page iv Federal Communications Commission (FCC) Declaration of Conformity (For USA Only) v WARNING LABEL Label location OUTSTANDING FEATURES vii Using the Built-In Camera to Uninterrupted Embroidering Duplicating a Pattern Print and Stitch (Combining the Embroidery and Printing) Page ix HOW TO USE THIS MANUAL CONTENTS x CONTENTS Chapter 1 Getting Ready 11 LOWER THREADING..................... .....................37 UPPER THREADING............................................46 CHANGING THE PRESSER FOOT .......................54 xi Chapter 5 Embroidery 181 Chapter 6 Embroidery Edit 261 Chapter 7 MY CUSTOM STITCH 313 Chapter 8 Appendix 325 Page NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Machine Front View Right-side/Rear View Needle and Presser Foot Section Embroidery Unit Operation Buttons CAUTION CAUTION Using the Flat Bed Attachment Using the Accessory Case Opening the Accessory Case Closing the Accessory Case Using the Accessory Trays Storing Bobbin Clips Using the Embroidery Unit Carrying Case Included Accessories Page Page Options Using the Spool Stand How to Assemble the Spool Stand CAUTION How to Remove Chapter 1 Getting Ready LOWER THREADING.....................................37 UPPER THREADING.......................................46 CHANGING THE PRESSER FOOT..................54 CHANGING THE NEEDLE..............................56 TURNING THE MACHINE ON/OFF WARNING CAUTION Page LCD SCREEN Home Page Screen Utility Stitch LCD Screen Page Page USB Connectivity Using USB Media or Embroidery Card Reader/USB Card Writer Module* Connecting the Machine to the Computer Using a USB Mouse Clicking a Key Changing Pages Page Using the Machine Setting Mode Key General settings Embroidery settings Changing the Pointer Shape When a USB Mouse Is Used Changing the Screen Saver Image Page Page Selecting the Initial Screen Display Choosing the Display Language Changing the Background Colors of the Embroidery Patterns Page Using the Sewing Machine Help Key Using the Operation Guide Function Example: Displaying information about upper threading Using the Sewing Guide Function Using the Pattern Explanation Function Example: Displaying information about Page LOWER THREADING Winding the Bobbin Using the Supplemental Spool Pin CAUTION Page Page Using the Spool Pin Using the Spool Stand Untangling Thread from Beneath the Bobbin Winder Seat Setting the Bobbin CAUTION Page Pulling Up the Bobbin Thread UPPER THREADING Upper Threading CAUTION Page Page Using the Twin Needle Mode CAUTION Page Page Using the Spool Stand Using the Spool Stand Using Threads that Unwind Quickly Using the Spool Net CHANGING THE PRESSER FOOT Removing the Presser Foot CAUTION Attaching the Presser Foot CAUTION Attaching the Walking Foot CAUTION CHANGING THE NEEDLE Page About the Needle Fabric/Thread/Needle Combinations CAUTION Chapter 2 Sewing Basics STITCH SETTINGS...............................................................................66 USEFUL FUNCTIONS..........................................................................69 SEWING Sewing a Stitch CAUTION Using the Foot Controller Sewing Reinforcement Stitches Sewing Curves Changing Sewing Direction Sewing a Seam Allowance of 0.5 cm or Less Sewing Heavyweight Fabrics If the Fabric does not Fit under the Presser Foot CAUTION Sewing Hook-and-Loop Fastener Sewing Lightweight Fabrics CAUTION Sewing Stretch Fabrics STITCH SETTINGS Setting the Stitch Width Setting the Stitch Length Setting the Thread Tension Proper Thread Tension CAUTION Upper Thread is Too Tight Upper Thread is Too Loose USEFUL FUNCTIONS Automatic Reinforcement Stitching Automatic Thread Cutting Using the Knee Lifter CAUTION Pivoting CAUTION Automatic Fabric Sensor System (Automatic Presser Foot Pressure) Needle Position Stitch Placement Locking the Screen Sew your project. When you are finished sewing, press again to unlock the screen settings. Checking the Needle Location in the Screen CAUTION Page Chapter 3 Utility Stitches SELECTING UTILITY STITCHES......................78 SEWING THE STITCHES.................................83 Page Selecting a Stitch Turn the main power to ON and press to display the utility stitches. Press the key of the stitch you want to sew. Use to select the category you want. Using the Mirror Image Key Using the Image Key Saving Your Stitch Settings Saving Settings Retrieving Saved Settings SEWING THE STITCHES Straight Stitches aLeft needle position bMiddle needle position aReverse stitch bReinforcement stitch Page Changing the Needle Position (Left or Middle Needle Position Stitches Only) Example: Left/Middle needle position stitches Aligning the Fabric with a Mark on the Needle Plate or Bobbin Cover (with Mark) Aligning the Fabric with the Vertical Stitch Alignment V Foot Using the Straight Stitch Needle Plate and the Straight Stitch Foot Basting Dart Seam Gathering Flat Fell Seam Pintuck Zigzag Stitches Attach presser foot J. Select a stitch. Overcasting (Using a Zigzag Stitch) aNeedle drop position Patchwork (for Crazy Quilt) Sewing Curves (Using a Zigzag Stitch) Cord Guide Bobbin Cover (Using a Zigzag Stitch) Elastic Zigzag Stitches Attach presser foot J. Select a stitch. Tape Attaching Stretch the tape flat. While stretching the tape flat, sew the tape to the fabric. Overcasting Overcasting Using Presser Foot G Select a stitch and attach presser foot G. Lower the presser foot so that the presser foot guide is set flush against the edge of the fabric. Sew along the presser foot guide. Overcasting Using Presser Foot J Select a stitch and attach presser foot J. Sew with the needle dropping slightly off the edge of the fabric. aNeedle drop position Overcasting Using the Side Cutter By using the side cutter, you can do overcasting while cutting the fabric. Thread the needle (see page 46). Follow the steps on page 54 to remove the presser foot. Position the fork on the side cutters operating lever onto the needle clamp screw. Page Lower the presser foot and start. When Sewing Straight Stitches While Using the Side Cutter Quilting Page Page Piecing Select or and attach presser foot J. Align the edge of the fabric with the edge of the presser foot, and start sewing. Quilting Select , or . Appliqu Quilting with Satin Stitches width control back to OFF. Free Motion Quilting Using Free motion Quilting Foot C page 86). Page Page Echo Quilting Using the Free Motion Echo Quilting Foot E Page Page Blind Hem Stitches Sew a blind hem according to the following procedure. Turn the skirt or pants wrong side out. Fold the fabric along the desired edge of the hem, and press. Fold back the fabric inside along the basting line. Page If the Needle Catches Too Much of the Hem Fold If the Needle does not Catch the Hem Fold Appliqu Appliqu Sharp Curves Appliqu Corners Shelltuck Stitches Scallop Stitches Crazy Quilting Smocking Stitches Fagoting Tape or Elastic Attaching Page Heirloom Hemstitching (1) (Daisy Stitch) Example: Illustration of finished product Hemstitching (2) (Drawn Work (1)) CAUTION Hemstitching (3) (Drawn Work (2)) One-step Buttonholes With one-step buttonholes, you can make buttonholes appropriate to the size of your button. Page Page Sewing Stretch Fabrics Odd Shaped Buttons/Buttons that do Not Fit into the Button Holder Plate Four-step Buttonholes Four-step buttonholes are sewn as shown below. Mark the position and length of the buttonhole on the fabric. aMarks on fabric bFinished stitching When changing the stitch settings, make sure that all stitch set tings are changed to match. Page Darning Use darning stitches for mending and other applicat ions. Darning is performed by sewing from the front of the presser foot to the back as shown below. aReinforcement stitches Select a stitch, and attach buttonhole foot A. Page Bar Tacks Bar Tacks on Thick Fabrics Button Sewing CAUTION Attaching 4 Hole Buttons Attaching a Shank to the Button Eyelet Multi-directional Sewing (Straight Stitch and Zigzag Stitch) Zipper Insertion Centered Zipper Inserting a Side Zipper Page Edge Sewing Attach the vertical stitch alignment foot V. Peel off the transparent sheet of the edge sewing sheet. Page Page Page Example: When a straight stitch is selected (example: ) Lower the presser foot. Press the Start/Stop button to start edge sewing. Page Chapter 4 Character/Decorative Stitches SELECTING STITCH PATTERNS SELECTING STITCH PATTERNS Press , then to display the screen below. Stitch Selection Screens Page Page Deleting Characters Adjusting the Character Spacing Press to adjust character spacing. SEWING STITCH PATTERNS Sewing Attractive Finishes Basic Sewing CAUTION Making Adjustments Page EDITING STITCH PATTERNS Character/Decorative Stitches EDITING STITCH PATTERNS EDITING STITCH PATTERNS Page Page Returning to the Beginning of the Pattern Checking the Image Page COMBINING STITCH PATTERNS Page Combining Large and Small Stitch Patterns Page Making Step Stitch Patterns (for 7mm Satin Stitch Patterns Only) Page Page Stitch Data Precautions Types of Stitch Data that can be Used Types of USB Devices/Media that can be Used Computers and Operating Systems with the Following Specifications can be Used Precautions on Using the Computer to Create and Save Data CAUTION Saving Stitch Patterns in the Machines Memory Choose a stitch pattern to delete. Page Saving Stitch Patterns to USB Media Saving Stitch Patterns in the Computer Retrieving Stitch Patterns from the Machines Memory Recalling from USB Media Page Recalling from the Computer Page Chapter 5 Embroidery BEFORE EMBROIDERING.....................................182 SELECTING PATTERNS..........................................186 VIEWING THE SEWING SCREEN..........................196 PREPARING THE FABRIC......................................198 BEFORE EMBROIDERING Embroidery Step by Step Follow the steps below to prepare the machine for embroidery. Attaching Embroidery Foot W CAUTION Attaching the Embroidery Unit About the Embroidery Unit CAUTION Removing the Embroidery Unit SELECTING PATTERNS Copyright Information Pattern Selection Screens Page Page Selecting Alphabet Character Patterns Example: Entering Blue Sky. Page Selecting Frame Patterns Page Selecting Patterns from Embroidery Cards About Embroidery Card Reader (Sold Separately) and USB Card Writer Module* About Embroidery Cards (Sold Separately) Page VIEWING THE SEWING SCREEN VIEWING THE SEWING SCREEN There is an explanation of additional key functions on the next p age. VIEWING THE SEWING SCREEN Embroidery Using these keys, you can change the size of the pattern, rotate the pattern, etc. PREPARING THE FABRIC Attaching Iron-on Stabilizers (Backing) to the Fabric CAUTION Page PREPARING THE FABRIC Hooping the Fabric in the Embroidery Frame ab Types of Embroidery Frames aHighlighted: Can be used bShaded: Cannot be used CAUTION Inserting the Fabric Using the Embroidery Sheet Embroidering Small Fabrics or Fabric Edges Embroidering Small Fabrics Embroidering Edges or Corners Embroidering Ribbons or Tape ATTACHING THE EMBROIDERY FRAME Page CONFIRMING THE PATTERN POSITION Page Following message appears. Press . Checking the Pattern Position Previewing the Completed Pattern CAUTION Page SEWING AN EMBROIDERY PATTERN Sewing Attractive Finishes CAUTION Embroidery Needle Plate Cover Page Sewing Embroidery Patterns Which Use Appliqu Page PRINT AND STITCH (COMBINING EMBROIDERY PATTERNS AND PRINTED DESIGNS) Selecting a Pattern Checking Only the Embroidery Pattern Outputting the Background Image and Positioning Image Use USB media or the computer to output the following three images from the machine. Using USB Media Insert the USB media into the primary (top) USB port on the machine. Select the pattern, and then press . Using a USB Cable Printing the Background and Embroidery Position Sheet Page ADJUSTMENTS DURING THE EMBROIDERY PROCESS If the Bobbin Runs Out of Thread If the Thread Breaks During Sewing Restarting from the Beginning Resuming Embroidery After Turning Off the Power Page MAKING EMBROIDERY ADJUSTMENTS Adjusting Thread Tension Correct Thread Tension Upper Thread is Too Tight Upper Thread is Too Loose Adjusting the Alternate Bobbin Case (with No Color on the Screw) Correct Tension Bobbin Thread is Too Loose Bobbin Thread is Too Tight Using the Automatic Thread Cutting Function (END COLOR TRIM) Press to turn off the automatic thread cutting function. CAUTION Using the Thread Trimming Function (JUMP STITCH TRIM) Selecting the Length of Jump Stitch Not to Trim Adjusting the Embroidery Speed Changing the Thread Color Display Changing the Embroidery Frame Display MAKING EMBROIDERY ADJUSTMENTS Embroidery REVISING THE PATTERN Changing the Pattern Position CAUTION Page Changing the Size Press to return to the or iginal screen. Rotating the Pattern Select the angle of rotation for the pattern. Page Changing the Density (Alphabet Character and Frame Patterns Only) Changing the Colors of Alphabet Character Patterns Embroidering Linked Characters Example: Linking DEF to the characters ABC Page Page Embroidery Data Precautions Types of Embroidery Data that can be Used Types of USB Devices/Media that can be Used CAUTION Computers and Operating Systems with the Following Specifications can be Used Precautions on Using the Computer to Create and Save Data Tajima (.dst) Embroidery Data Trademarks Saving Embroidery Patterns in the Machines Memory CAUTION Select the pattern you want to delete. Page Saving Embroidery Patterns to USB Media Saving Embroidery Patterns in the Computer Retrieving Patterns from the Machines Memory Recalling from USB Media Page Recalling from the Computer Page EMBROIDERY APPLICATIONS Using a Frame Pattern to Make an Appliqu (1) Using a Frame Pattern to Make an Appliqu (2) Page Sewing Split Embroidery Patterns Page Chapter 6 Embroidery Edit EXPLANATION OF FUNCTIONS..................262 SELECTING PATTERNS TO EDIT..................263 EDITING PATTERNS.....................................267 COMBINING PATTERNS..............................291 VARIOUS EMBROIDERING FUNCTIONS.... 295 EXPLANATION OF FUNCTIONS SELECTING PATTERNS TO EDIT Embroidery Edit SELECTING PATTERNS TO EDIT See page 187 for more information on each categorys sel ection screen. Page Page Page Embroidery Edit EDITING PATTERNS If a key display is light gray, you cannot use that function wi th the selected pattern. Page Moving the Pattern Rotating the Pattern Select the angle by which the pattern is rotated. Press to return to the or iginal screen. Changing the Size of the Pattern Press . Deleting the Pattern Changing the Configuration of Alphabet Character Patterns Page Reducing Character Spacing Separating Combined Character Patterns Changing the Color of Each Alphabet Character in a Pattern Embroidering Linked Characters Example: Linking DEF to the characters ABC Page Changing the Thread Color Creating a Custom Thread Table Page Page Thread Table from the List Choosing a Color from the Custom Thread Table Designing Repeated Patterns Sewing Repeated Patterns Select a pattern, and then press . Select the direction in which the pattern will be repeated. Page Repeating One Element of a Repeated Pattern Color Sorting Repeated Patterns Page Assigning Thread Marks Duplicating a Pattern After Editing COMBINING PATTERNS Editing Combined Patterns Page Selecting combined embroidery pat- terns Sewing Combined Patterns VARIOUS EMBROIDERING FUNCTIONS Uninterrupted Embroidering Basting Embroidery Creating an Appliqu Piece Creating an Appliqu Piece Page Page Page Using a Frame Pattern for the Out- line Page Page Page Page Page PRINT AND STITCH (COMBINING EMBROIDERY PATTERNS AND PRINTED DESIGNS) Selecting a Pattern Checking Only the Embroidery Pattern Outputting the Background Image and Positioning Image Using USB Media Using a USB Cable Printing the Background and Embroidery Position Sheet Page Page Chapter 7 MY CUSTOM STITCH DESIGNING A STITCH DESIGNING A STITCH MY CUSTOM STITCH Examples of Custom Stitches ENTERING STITCH DATA ENTERING STITCH DATA Page Page Moving a Point Moving Part or All of the Design Inserting New Points Page USING STORED CUSTOM STITCHES Storing Custom Stitches in Your List Retrieving Stored Stitches Page Chapter 8 Appendix CARE AND MAINTENANCE Cleaning the LCD Screen Cleaning the Machine Casing Cleaning the Race CAUTION Cleaning the Cutter in the Bobbin Case Area CAUTION About the Maintenance Message CAUTION ADJUSTING THE SCREEN Touch Panel is Malfunctioning TROUBLESHOOTING Page Page Page Page ERROR MESSAGES Page Page Page Page Page Page Alarm Sounds Memo SPECIFICATIONS SPECIFICATIONS * Please be aware that some specifications may change without notice. UPGRADING YOUR MACHINES SOFTWARE Upgrade Procedure Using USB Media Upgrade Procedure Using Computer Page STITCH SETTING CHART Page Page Page Page Page Page Page Page INDEX Page Page Page Page Page Computerized Embroidery and Sewing Machine X1_BrotherE_OM_cover C M Y K Operation Manual Operation Manual