SERVICE (cont.)

CONTROL BOARD (CONT.)

11.With a voltmeter check the voltage across the terminals of the inlet solenoid valve. Connect the dispenser to the power source. After a 10 second delay, the indication must be :

a)120 volts ac for two wire 120 volt models.

b)120 volts ac for three wire 120/208 or 120/240 volt models.

c)240 volts ac for two wire 240 volt models.

d)230 volts ac for two wire 230 volt models.

12.Move the probe’s flat end to the dispenser housing. The indication must be 0.

13.Move the probe’s flat end away from the housing. After a 5 second delay, the indication must, again, be:

a)120 volts ac for two wire 120 volt models.

b)120 volts ac for three wire 120/208 or 120/240 volt models.

c)240 volts ac for two wire 240 volt models.

d)230 volts ac for two wire 230 volt models.

14.Disconnect the dispenser from the power source.

If the voltage is present as described, re-install the probe. The liquid level control circuitry is operating properly.

If the voltage is not present as described, check the pink probe wire and green tank wire for continuity and check the overflow protection switch.

Hopper Motor Control Circuitry:

1.Disconnect the dispenser from the power source.

2.With the voltmeter, back probe check the voltage across pins 1 & 2 of the eight pin J1 connector on the wiring harness. Connect the dispenser to the power source. The indication must be 24 volts ac from the transformer.

3.Disconnect the dispenser from the power source.

If voltage is present as described, proceed to step 4. If voltage is not present as described, refer to the wiring diagram and check the dispenser wiring harness.

4.Check that the “Rinse/Run” switch is in the “Run” position.

5.With a voltmeter check the voltage across the red

(+) terminal and the black (-) terminal of the auger motor. Connect the dispenser to the power source. Press the appropriate dispense switch. After a delay of about .6 seconds, the indication must be between +4.0 and +24.5 volts dc.

If the voltage is present as described, the hopper motor control circuitry is operating properly.

If the voltage is not present as described, replace the control circuit board.

Whipper Motor and Dispense Solenoid Circuitry:

1.Disconnect the dispenser from the power source.

2.With a voltmeter, back probe check the voltage across pins 1 & 2 of the eight pin J1 connector on the wiring harness. Connect the dispenser to the power source. The indication must be 24 volts ac.

3.Disconnect the dispenser from the power source.

If voltage is present as described, proceed to step 4. If voltage is not present as described, refer to the wiring diagram and check the dispenser wiring harness.

4.Check that the RINSE/RUN switch is in the “Rinse” position.

5.With a voltmeter, back probe check the voltage across pins 2 & 4 of the six pin J2 connector on the wiring harness. Connect the dispenser to the power source. The indication must be:

a)120 volts ac for two wire 120 volt models

b)120 volts ac for three wire 120/208 or 120/240 volt models

c)240 volts ac for two wire 240 volt models.

d)230 volts ac for two wire 230 volt models.

6.Disconnect the dispenser from the power source.

7.With a voltmeter check the voltage across the terminals of the appropriate dispense solenoid. Connect the dispenser to the power source. Press the appropriate dispense switch. The indication must be :

a)120 volts ac for two wire 120 volt models

b)120 volts ac for three wire 120/208 or 120/240 volt models

c)240 volts ac for two wire 240 volt models.

d)230 volts ac for two wire 230 volt models.

21

42672 122209

 

Page 20 Page 22
Page 21
Image 21
Bunn FMD-4, FMD-5 manual Hopper Motor Control Circuitry, Check that the RINSE/RUN switch is in the Rinse position
Page 20 Page 22

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents