SERVICE (cont.)

AUGER DRIVE COMPONENTS (all Models)

FMD-4 shown

J1

J2

J4

J3

J1

J2

J4

J3

P4095

FIG. 2 AUGER DRIVE COMPONENTS

Location

The auger components are located inside the bottom part of the hopper except for the auger drive bracket, spacer and retaining clip, which are located on the outside rear of the hopper base. The auger motor is located on the lower right rear of the motor mounting panel. Refer to Fig. 3 for disassembly and assembly.

Test Procedures - Auger Motor

1.Disconnect the dispenser from the power source.

2.Disconnect the white/red wire and the white wire from the hopper drive board (FMD-1) or relative wires from the control board(all other models).

3.Check the voltage across the white/red wire and the white wire with a voltmeter. With the rinse/ run switch in the run (lower) position, connect the dispenser to the power supply. The indication must be:

a)120 volts ac for two wire 120 volt models. b)120 volts ac for three wire120/208 volt or 120/240 volt models.

c)230 volts ac for two wire 230 volt models.

4.Disconnect the dispenser from the power supply.

If voltage is present as described, proceed to #5.

If voltage is not present as described, refer to the wiring diagram and check the dispenser wiring harness.

5.Check the voltage across the positive (red wire) terminal and the negative (black wire) terminal on the auger motor with a voltmeter. With the rinse/ run switch in the run (lower) position press and hold the dispense switch. Connect the dispenser to the power supply. After a .6 second delay the indication must be 4.0 to 24.5 volts dc.

If voltage is present as described, the auger motor drive is operating properly. If auger does not turn, replace the auger motor.

If voltage is not present as described, check the auger hopper drive board.

Removal, Cleaning and Replacement

Hopper & Auger (FMD-1,4)

1.Open the dispenser door and raise the top front cover.

2.Lift the hopper assy (15) over the pins on hopper support plate (11) and slide hopper assembly out the front of the dispenser.

3.Remove hopper lid (1) and empty product.

4.Pull off the ejector elbow (14).

5.Remove retainer clip (10) and washer (9) from the bottom of the hopper base (8).

6.Remove whipper shaft (3), wiper blade (4) and wiper drive gear (5) from the hopper base (8).

7.Remove auger wire (13) by pulling it out the front of the hopper base (8).

8.Remove auger drive bracket (6) by unscrewing left hand threads from auger drive shaft (12).

9.Slide spacer (7) and auger drive shaft bracket (6) off of the auger drive shaft (12).

10.Remove auger drive shaft (12) from hopper base

(8).

11.Wash components in a mild solution of dish deter- gent using a bristle brush when needed.

12.Rinse and dry each item thoroughly.

13.Check for damaged or broken components, replace any if necessary and reassemble hopper assem- bly.

14.Install hopper assy (15) in the dispenser by sliding hopper assy on the hopper support plate (11) until the slot in the rear of the hopper base (8) seats against the pins in the hopper support plate (11).

14

42672 122209

 

Page 14
Image 14
Bunn FMD-5, FMD-4 manual Service Auger Drive Components all Models, Location, Test Procedures Auger Motor

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.