Fire extinguishers / smoke detectors
All homes with a solid fuel burning fireplace should have at least one fire extinguisher in a central location known to all, and at least one smoke detector in the room containing the fireplace. If it sounds an alarm, correct the cause but do not deactivate or relocate the smoke detector.
Install the blower and housing using 4 of the screws supplied.
Loosen the 2 screws securing the thermodisc bracket and slide the bracket forward until the thermodisc is touching the heat shield. Secure in place by tightening the screws.
Fuel loading and burn cycle
For maximum efficiency, when the stove is thoroughly hot, load it fully to the top of the door opening and burn at a medium low setting. Maximum heat for minimum fuel (optimum burn) occurs when the stove top temperature is between 500°F (260°C) and 600°F (315°C). The cleanness of the glass is a good indicator of your operating efficiency. Not enough heat is produced when only one or two pieces of wood are burned or the wood may not burn completely. A minimum of three pieces are needed to encase a bed of coals that sustains the fire.
Loosely stacked wood burns quicker than a tightly packed load. Wood burns in cycles rather than giving a steady output of heat. It is best to plan these cycles around your house hold routine so that only enough coals are left to start the next load. In the evening, load your stove, at least, a
It produces more heat and less soot or creosote. Do not burn ocean beach wood. Its salt content can produce a metal eating acid. When refueling open the door slowly to prevent smoke spillage. Use a pair of long gloves (barbecue gloves) when feeding the fire. Because these stoves burn at the front, they are clean and efficient, but they are also very hot and gloves are useful. Keep a small steel shovel nearby to use as a poker and to remove ashes. Do not store the wood within 3 feet (1m) of the stove.
EP63 OPTIONAL BLOWER KIT
Remove the 4 screws from the rear plate of the stove.
Replace the screws removed with the 4 spacers supplied.
Install the rear heat shield using the 4 screws removed and secure to the 4 spacers.
The flue collar shield is only needed if the flue collar is in the top exit position. If the flue collar is in the rear exit position, the flue collar shield can be discarded.
Install the flue collar shield to the rear heat shield, using 2 of the screws supplied.
Ash removal procedures
CAUTION : Risk of excessive temperatures. Keep the ash door closed during firing of the heater.
It is essential to keep the grate free of a heavy build up of ashes.
When burning solid fuel, always empty the ash pan at least once a day or whenever it is full of ashes. Never allow the ashpan to overfill thereby allowing ash to be in contact with the underside of the grate. If this condition is allowed, the grate will wear out prematurely.
Hot ashes may be kept in a metal container with a tight fitting lid. Keep the closed container on a noncombustible floor or ground, well away from all combustible materials. The ashes should be retained in the closed container until all cinders have thoroughly cooled. Cold wood ashes can be used on the garden or in the compost.
DO’S
1.Build a hot fire
2.Use only dry wood.
3.Several pieces of medium sized wood are better than a few big pieces.
4.Clean chimney regularly.
5.Refuel frequently using medium sized wood.
6.“Fine Tune” the air settings for optimum performance.
DON’TS
1.Take ash out immediately. Let it accumulate to a depth of at least one inch. A good ash layer provides for a longer lasting and better burning fire.
2.Burn wet wood.
3.Close the door too soon or damper down too quickly.
4.Burn one large log rather than two or three smaller, more reasonably sized logs.
5.Burn at continually “low setting”, if glass door is constantly blackened. This means the firebox temperature is too low.
EP90-K OPTIONAL SCREEN KIT
The
This kit is not applicable for mobile homes.
10
