SERVICE (cont.)

HOT WATER DISPENSE SOLENOID VALVE (FMD-2FD,DBC-2FD,-3,DBC-3)

FMD DBC-3 shown

P4102

FIG. 46 HOT WATER DISPENSE

SOLENOID VALVE

Location:

The hot water solenoid valve is located on the left side of the tank.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.With a voltmeter check the voltage across the white and blue wires at the solenoid valve. Connect the dispenser to the power source. The indication must be:

a)120 volts ac for two wire 120 volt models

b)120 volts for three wire 120/208 or 120/240 volt models

c)240 volts ac for two wire 240 volt models.

d)230 volts ac for two wire 230 volt models.

3.Disconnect the dispenser from the power source. If voltage is present as described, proceed to #4.

If voltage is not present as described, refer to the wiring diagram and check dispenser wiring harness.

4.Disconnect the white and blue wires from the so- lenoid valve.

5.Check for continuity across the solenoid valve coil terminals.

If continuity is present as described, reconnect the white and blue wires to the solenoid.

If continuity is not present as described, replace the solenoid valve.

6.Check the solenoid valve for coil action. Connect the dispenser to the power source. Listen carefully in the vicinity of the solenoid valve for a “clicking” sound as the coil magnet attracts.

7.Disconnect the dispenser from the power source. If the sound is heard as described and water will not pass through the solenoid valve, there may be a block- age in the water line before the solenoid valve or the solenoid valve may require inspection for wear, and removal of waterborne particles.

If the sound is not heard as described, replace the solenoid valve.

Removal and Replacement:

1.Remove the white and blue wires from the solenoid valve.

2.Turn off the water supply to the dispenser.

3.Drain enough water from the tank (approximately 2.0 gallons) so the water level is below the dispense valve mounting hole.

4.Disconnect the water line from the solenoid valve.

5.Loosen the #10-32 screw securing the solenoid valve to side of the tank. Twist the solenoid valve clockwise and remove solenoid valve.

6.Using the #10-32 screw install new solenoid valve on side of the tank.

7.Push the water line onto the tube on bottom of solenoid valve.

8.Refer to schematic wiring diagrams when recon- necting the wires.

P1995.50

FIG. 47 HOT WATER DISPENSE

SOLENOID VALVE WIRING

48

42672 122209

 

Page 47 Page 49
Page 48
Image 48
Bunn FMD-5, FMD-4 manual HOT Water Dispense Solenoid Valve FMD-2FD,DBC-2FD,-3,DBC-3
Page 47 Page 49

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents