Burley TC700 Series Camera Using Auxiliary Controls, Commands Using Pre-Position Controls

Camera - Using Auxiliary Controls

Camera	Aux	Description	On/Off	Notes
Function	No.
BL_COMP	20	Backlight	On/off	1
		Compensation
HIGH-LIGHT	21	Highlight	On/off	1, 7
SHUTTER_ADJ	22	Shutter Adjust	Inc/dec	1
SHUTTER	23	Shutter	On/off	1
WHITE_BALANCE	30	White Balance	Auto/	8
			manual
RED	31	Red Adjust	Inc/dec	1, 8
BLUE	32	Blue Adjust	Inc/dec	1, 8
R_Y_HUE	33	R-Y Hue Adjust	Inc/dec	3, 8
B_Y_HUE	34	B-Y Hue Adjust	Inc/dec	3, 8
FIXED_WB	35	Fixed	Indoor/out	1, 8
		White Balance	door
FACTORY_	40	Factory Default	Set/---	1,3
DEFAULTS		Settings
LL_PHASE	41	Adjust LL Phase	Inc/dec	3
		Delay
SYNC	42	Sync Mode	ll/xtal	3
AGC	43	AGC	On/off	3

Note: Auto-pan is discontinued when the manual pan control (joystick) is used.

Auto-iris and auto-focus revert to manual mode when the manual iris and focus controls are used, respectively.

Switching to manual iris or manual focus from auto mode reverts to the last manual setting used.

Auto-focus is activated automatically upon pan or tilt when Auto-focus Activation is on (AUX #12).

Manual iris is activated automatically upon activating (ON) Backlight Compensation.

Commands Using Pre-Position Controls

Receiver/Driver	Pre-	Description	SET/SHOT	Notes
Function	Position
	No.
Pre-position	1-60	---	Set/show	4
Future	61-100	---	----/----	--
PP Expansion
Auto-pan	101	---	Set/show	2
left limit
Auto-pan	102	---	Set/show	2
right limit
Home Position	110	---	Recalibrate/	--
			show
Disable/Enable	901-960	---	Disable/	6
PP			enable
Global Disable/	900	---	Disable/	6
Enable PP			enable

Notes:

1.The following settings are stored with pre-position scenes:

Pan position. Tilt position. Zoom position.

Focus mode AUTO/MANUAL. Focus position for MANUAL mode. Iris mode AUTO/MANUAL.

Iris ALC/LEVEL for AUTO mode or position for MANUAL mode.

White Balance mode AUTO/MANUAL (color cameras only).

Red content and Blue content for MANUAL mode (color cameras only).

Shutter mode ON/OFF. Shutter setting for ON mode. Backlight compensation ON/OFF.

Highlight ON/OFF (monochrome cameras only).

2.The following settings are stored as a default setting in nonvolatile memory (EEPROM) on R/D board and are used to restore settings at power-up:

Auto-pan left limit = 0 degrees. Auto-pan right limit = 359.9 degrees. Auto-pan speed = 30 degrees per second. Auto-focus activation = ON.

Auto-iris activation = ON. Auto-speed = OFF.

3.This setting stored as a default setting in nonvolatile memory in camera.

4.Pre-position #1 (if set) is automatically called-up upon power-up just after the homing sequence.

5.Scan direction determined by last manual pan direction.

6.Pre-positions can be disabled such that they do not operate during pre-position tour. They are still available for manual call-up.

7.Applies to monochrome cameras only.

8.Applies to color cameras only.

Auto-Playback

Applicable only to units fitted with this feature.

Recording Playback:

1.Position AutoDome to the point where playback is to start.

2.Press On, AUX 100, ENTER.

3.Begin controlling the AutoDome.

4.At the completion of controlling the AutoDome, press

Off, AUX 100, ENTER.

Note: If you run out of record time prior to issuing the stop record command, the AutoDome will position itself at the beginning and not move until the joystick is released for one second.

7