Burley TC700 Series user manual Description, Installation, Operation

DESCRIPTION

The TC700 Series AutoDome™ systems are quiet, lightweight, and discreet surveillance dome systems containing high sensitivity 1/3-inch image format full performance monochrome or color CCD cameras with a 10:1 auto-iris, auto-focus zoom lens, a high-speed pan/tilt, and an intelligent, integral receiver/driver. The one-piece camera, lens, pan/tilt, and receiver/driver module is housed in a domed enclosure. They are available in suspended ceiling, hard ceiling recessed, surface, and pendant mount models. Pendant mount models are available for indoor or outdoor applications.

INSTALLATION

Attention: Installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable local codes.

Attention: L'installation doit être effectuée uniquement par du personnel de service qualifié conformément à la réglementation du Code Electrique National ou à la réglementation locale.

Achtung! Die Installation sollte nur von qualifiziertem Kundendienstpersonal gemäß jeweilig zutreffender Elektrovorschriften aus- geführt werden.

Atención: La instalación de este equipo debe ser realizada por personal capacitado, solo en acuerdo, y en cumplimiento de normas del "National Electric Code" (Código Eléctrico Nacional) ó las normas del Gobierno Nacional Local.

Removing Module From Carton

Refer to ILLUSTRATIONS for component description.

CAUTION: Keep in foil bag until grounded at unit. Be sure to observe all safety measures for static control when working with this unit while out of its enclosure. Otherwise, static damage may result.

For removal from foil bag and installation instructions, see TC700 Series - Camera, Lens, Pan/Tilt, and

Receiver/Driver Modules Installation under INSTALLATION in the Installation and Operating Instructions supplied with the particular Backbox Module ordered.

CAUTION: Do not handle the unit by the circuit board because this may result in physical damage to the unit.

OPERATION

Camera Control

These units, as shipped, are factory adjusted as described below:

Line-lock mode enabled with zero degree phase delay.

AGC on.

Backlight compensation off. Electronic shutter off.

Automatic white balance on (color cameras only).

Changing Operating Modes

The AutoDome unit operating modes can be changed using either a TC8135B Series Controller/Follower or an Allegiant series keyboard. An Allegiant series keyboard is required to take full advantage of all the various features available. See Camera Commands for description of various camera operating adjustments.

AutoDome Commands

Receiver/Driver - Using Auxiliary Controls

Receiver/Driver	Aux	Description	On/Off	Notes
Function	No.
Scan	1	Auto-pan without	On/off	5
		limits
Auto-Pan	2	Auto-pan between	On/off	--
		limits
Pre-Position Tour	8	--	On/off	--
Set Scan/auto-pan	14	--	Inc/dec	2
speed
Set tour period	15	Sets pause between	Inc/dec	2
		tour callups
Auto-Speed	16	Enables/disables	On/off	2
		auto-speed

Lens - Using Auxiliary Controls

Lens	Aux	Description	On/Off	Notes
Function	No.
Iris Control	3	--	Auto/	1
			manual
Focus Control	4	--	Auto/	1
			manual
Auto-iris ALC adj	10	--	Peak/ave	1
Auto-iris Level adj	11	--	Inc/dec	1
Auto-focus	12	Activates AF upon	On/off	2
Activation		movement
Auto-iris Activation	13	Activates AI upon	On/off	2
		movement

Auto-Speed (AUX 16)

Auto-speed On: Issuing this command provides variable pan speed when unit is operated from a fixed speed location. The pan speed starts slowly and increases as the pan control is held on. The speed resets to slow when the pan control is released. Note: DIP Switch S2005.4 must be in the OFF position to use this command; see DIP Switch Settings in the applicable Installation and Operating Instructions for additional information.

6