IV. Venting / Air Intake Piping

A.General Guidelines

1.Vent system installation must be in accordance with these instructions and applicable provisions of local building codes. Contact local building or fire officials about restrictions and installation inspection in your area.

2.The LE®DV Series is designed as a Direct Vent boiler. In this configuration, all air for combustion is supplied directly to the burner from outdoors and flue gases are vented directly outdoors (through wall). See Figures 10 and 11. The LEDV may be side-wall vented with combustion air supplied from indoors. This configuration may be used in installations where infiltration provides adequate air for combustion and ventilation. Flue gases are still vented directly outdoors (through wall).

3.For minimum clearances to combustible materials refer to Figure 2.

4.Maximum wall thickness that vent terminal may be installed through is 10 inches.

WARNING

DO NOT locate vent terminal where exposed to prevailing wind. Moisture and ice may form on surfaces around vent termination. To prevent deterioration, surfaces should be in good repair (sealed, painted, etc.).

5.Locate the vent terminal so vent pipe is short and direct, and at a place on the exterior wall that complies with the minimum distances as specified in

Figure 8 and listed below. The vent terminal must be located:

a.Not less than 12 inches above grade plus snow accumulation (as measured to the nearest edge of terminal).

b.Not less than 3 feet to center of terminal above any forced air inlet located within 10 feet.

c.Not less than 1 foot to center of terminal horizontally from any door, window or gravity air inlet.

d.Not less than 7 feet to center of terminal above a public walkway.

e.Not less than 3 feet to center of terminal from an inside corner of an L-shaped structure.

f.Not less than 1 foot from nearest surface of terminal to a roof soffit.

g.Not directly above, or not less than 6 feet horizontally from an oil tank vent or gas meter.

h.Not less than 2 feet from nearest surface of terminal to an adjacent building.

Figure 8: Vent Terminal Location

12

Page 11 Page 13
Page 12
Image 12
Burnham 81433101R16-1/10 manual IV. Venting / Air Intake Piping, General Guidelines
Page 11 Page 13

81433101R16-1/10 specifications

The Burnham 81433101R16-1/10 is a highly regarded component within the realm of heating, ventilation, and air conditioning (HVAC) systems, known for its reliability and performance. This specific part is designed to enhance the efficiency of heating systems, making it an essential component for both residential and commercial applications.

One of the standout features of the Burnham 81433101R16-1/10 is its durable construction. Made with high-quality materials, this product is built to withstand the rigors of continuous operation in various environmental conditions. Its robust design ensures a longer lifespan, reducing the need for frequent replacements and maintenance, which ultimately saves on operational costs.

The Burnham 81433101R16-1/10 incorporates advanced technology to optimize energy usage. This part is engineered for high efficiency, meaning that it works to convert a maximum amount of energy into heat with minimal waste. The integration of cutting-edge technology ensures that users experience significant energy savings, which not only helps in reducing utility bills but also contributes positively to environmental sustainability.

In terms of compatibility, the Burnham 81433101R16-1/10 is designed to work seamlessly with various heating systems. This makes it a versatile choice for technicians and homeowners alike, as it can be easily integrated without extensive modifications. The ease of installation is another appealing characteristic, allowing for quicker setups that minimize downtime.

Furthermore, this component prioritizes safety, featuring built-in mechanisms that help prevent overheating and other potential hazards. This focus on safety reassures users that their heating systems can operate efficiently without compromising the well-being of their households or properties.

The Burnham 81433101R16-1/10 is also known for its user-friendly design. Technicians find that maintenance and inspection processes are straightforward, allowing for easy access to components for troubleshooting or routine checks. This practical feature enhances user satisfaction and simplifies operational management.

Overall, the Burnham 81433101R16-1/10 exemplifies a commitment to quality, efficiency, and safety in HVAC applications. Its combination of durability, advanced technology, and versatile compatibility makes it a valuable choice for anyone looking to enhance their heating system's performance. By opting for the Burnham 81433101R16-1/10, users can enjoy efficient heating solutions that meet their needs for comfort and energy conservation.
Top Page Image Contents