SECTION I
INTRODUCTION AND DESCRIPTION
1-1 INTRODUCTION
We are pleased to have you as a Bush Hog cus- tomer. Your 305/306 Series Rotary Cutter has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition. Please read this manual thor- oughly. Understand what each control is for and how to use it. Observe all safety precautions decaled on the machine and noted throughout the manual for safe operation of implement. If any assistance or additional information is needed, con- tact your authorized Bush Hog dealer.
| Figure |
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
Support Yoke |
|
| Tailwheel | ||
Strut |
|
|
|
| |
|
|
|
| ||
|
|
| Gearbox |
| |
|
|
|
| Driveline |
|
|
|
|
|
|
|
|
| |
| The 305/306 Series rotary cutters (Figure | are |
|
|
|
|
|
|
|
|
|
|
| |
|
| Hitch Pin |
|
|
|
| Strongback |
|
| |||||
| designed for medium duty applications | such as |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| Skid |
|
|
|
| ||
| grass, corn stalks and light brush. These cutters are |
|
|
|
|
|
|
| ||||||
|
|
|
| Chains |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||
| single spindle with two |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||
| swinging blades reduce the shock of impact when a |
|
|
|
|
|
|
|
|
|
|
| ||
| stationary object is hit. Additional protection is pro- |
|
|
|
|
|
|
|
|
|
|
| ||
| vided by a slip clutch on the gearbox input | shaft. | A |
|
|
|
|
|
|
|
|
|
|
|
|
| NOTE: | Dealer or | purchaser may elect to delete | ||||||||||
| round blade holder allows the cutter to “ride over” |
| front and rear discharge shields (deflectors) at their | |||||||||||
| stumps and similar immovable objects. Models 305 |
|
| option. | Refer to “WARNING” in Section | |||||||||
| and 306 are attached to the tractor using a standard |
|
|
|
|
|
| NOTE | ||||||
| Cat. I, II, or III |
| All references made to right, left, front, rear, top or | |||||||||||
| and III quick hitch. Standard equipment includes dri- |
| bottom are as viewed facing the direction of forward | |||||||||||
| veline shields, clutch shields and front discharge |
| travel with implement properly attached to tractor. | |||||||||||
| shields (deflectors). |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Table 1 Technical Specifications |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SERIES |
|
| 305 |
|
|
| 306 |
|
|
|
| ||
| Cutting Width |
|
|
| 60” |
|
|
|
|
| 72” | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Transport Width |
|
|
| 65” |
|
|
|
|
| 79” | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Length |
|
|
| 101” |
|
|
|
|
| 113” | |||
| Hitch |
|
|
| ||||||||||
|
|
|
|
|
| and Cat. II & III Quick Hitch | ||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| Cutting Height |
|
| 2” - 12” |
|
|
| 2” - 12” | ||||||
| Cutting Capacity |
|
| 3” Diameter |
|
|
|
| 3” Diameter | |||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| Driveshaft |
|
| ASAE Category 4 or 5 |
| ASAE Category 4 or 5 | ||||||||
| Gearbox |
|
| 540 RPM (80 HP) |
| 540 RPM (90 HP) | ||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| Blades |
|
| 1/2” x 4” Uplift |
|
| 1/2” x 4” Uplift | |||||||
| Blade Tip Speed |
|
| 12,193 fpm |
|
| 14,632 fpm | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Blade Holder |
|
| Round |
|
|
|
| Round | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Top Deck |
|
| 7 Ga. Steel |
|
|
|
| 7 Ga. Steel | |||||
| Side Bands |
|
| 1/4” x 7” |
|
|
| 1/4” x 7” | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Minimum Tractor HP |
|
| 30 |
|
| 40 |
|
| |||||
|
|
|
|
|
|
|
|
|
|
| ||||
| Front & Rear Deflectors |
|
| Front chains are standard, rear chains are optional | ||||||||||
| Wheels |
|
| Laminated |
|
|
|
| Laminated | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Approximate Weight (lbs.) |
|
| 825 lbs. | 1 |
|
|
|
| 1078 lbs. 1 | ||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| 1 - Weight includes deflector chains front and standard |
| SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE |
|
|
|
|
|
|
| ||||
6
