Manuals / Cabletron Systems / Computer Equipment / Network Router

Cabletron Systems 510, 520 manual

Models: 510 520

1 106

Download 106 pages 2.25 Kb

<>

Specs Install Parts list Chapter Configuring the Router Connecting the Console Port Appendix a Problem Solving Restart with Factory Defaults Signaling Standards Restart with Current Settings Safety

Page 100

Page 99 Page 101

Image 100

Cabletron Systems 510, 520 manual

Page 99 Page 101

Related manuals

Manual 106 pages 2.25 Kb

Related pages

Contents

SmartSwitch Router 510 Installation and Configuration Guide Page By Cabletron Systems, Inc FCC Notice Cabletron SYSTEMS, INC. Program License Agreement Exclusion of Warranty and Disclaimer of Liability Declaration of Conformity Addendum Page Contents Chapter Configuring the Router Chapter Connecting the Console Port CableChapter Supporting Isdn for the SSR-510 Appendix C Product Specifications Appendix a Problem SolvingAppendix D Installation Information United Kingdom Contents Overview Using This GuideIntended Audience Structure of This Guide Chapter Title Description AppendixRelated Documentation Part Number Title DescriptionHow to install and use the trace Document Conventions Glossary Term DefinitionGetting Help Your email addressPage Chapter Contents Product IntroductionSSR-510 Router SSR-520 RouterConfiguration and Management FeaturesPerformance and Memory EasyStart Front Panel Components Front and Back Panel ComponentsIcon Name Description Refer to the Distributed Router Product Introduction Back Panel Components Name DescriptionBack Panel Layout Page Installing and Cabling Installing the Router in the Rack Mounting Shelf Rack Mounting Shelf, Router and Power Supply AssemblyAssembling the Rack Mount Shelf Step ActionAttaching Adhesive Strips Assembled Router and Rack Mount Shelf Cabling the Routers Cabling the SSR-510Step Action Installing the SSR-520Router Cabling the SSR-520Step Action Removing the Cables Removing the SSR-510 CablesRemoving the SSR-520 Cables Removing the SSR-520 CablesPage Connecting the Console Port Cable Signaling Standards Console Port Device CablingConnecting the Console Port Step ActionConsole Port Cabling Components Item DescriptionConfiguring the Router Using the Router Configurator to Configure the Router Step ActionStep Action Console Screens On the nextConfiguring the Router Using the CLI to Manually Configure the Router Type 3 and press Return as shown in the following example To configure the router using Go to the section titled EasyStart Stop ReturnPreconfigured Router Screen Using Menus to Set up the Router OptionRestart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration IP ConfigurationSet Snmp Read/Write Community SET Smnp READ/WRITE CommunityIN-BAND Interface IP Address Configuration Set In-Band Interface IP AddressSet Default Gateway SET IN-BAND Interface Default Gateway AddressGo to Local Console Enter yes to proceed. The following menu is then displayed Page Supporting Isdn for the SSR-510 Ordering Your Isdn Line Configuration ParameterPossible Values Obtaining a Network Termination Device Page Problem Solving Appendix ContentsNormal Powerup Event DescriptionSelf-Test Progress States These tests are run prior to the router OK LED being litOption card dpram setup if present LED Descriptions Off On Green Flashing NameLED Problem Solving Using the LEDs Symptom Probable Cause Corrective ActionRouter 500 Series System Symptom Probable Cause Corrective Action Page Connectors, Adapters and Cable Connections Pin Serial Port Connector Connector AssignmentsPin Assignment DTR a 10BaseT Port 8-pin MJ Connector Figure B-2 -pin MJ ConnectorH8571-J Adapter AdaptersH8575-A Adapter From Pin To X.21 Pin Signal Name Connector P1 Connector P2 Cable ConnectionsFrom Pin Connector To EIA422 Pin Signal Name Connector P2 Clock a From Pin Connector To V.35 Pin Signal Name Connector P2 From Pin Connector To EIA530A Pin Signal Name Connector P2 EIA530A Cable Connections BC12J-06 From Pin Connector To EIA423 Pin Signal Name Connector P2 19, 22, 25, 30 DTE Ground Speed Select 12, 29, 31, 34, 35 DTE Ground1 Speed Select Product Specifications Product Specifications Parameter SpecificationProduct Acoustical SpecificationsProdukt Connectors Connectors QuantityParts List Part Part NumberPage Installation Information United Kingdom Service Categories Power Rating, Router Isolation and Safety Status Host Power RatingSafety Status Router IsolationCable Approval Interface Cable Type Name Molding PinsSupported Cables Installation Information United Kingdom