Cambridge Audio 340Razur user manual OSD setup, Custom installation C.I. use, Reset/Back-up memory

Advanced bass management continued

Bass Augment can be a useful function with PLII material because this encoding type does not include an LFE Channel. This would normally mean that if all the speakers in your setup were set to ‘Large’, the subwoofer would in fact be inactive (as no bass has been re-directed plus there is no LFE channel). If it is desired to have the subwoofer running with all Large Speakers and PLII encoding, enable Bass Augment for PLII and then set the Crossover point and level by ear. A Sub channel will now be created from the Front Left and Right channels without filtering them. As with all adjustments it is a good idea to experiment to determine what works best with your particular setup.

Note: In Advanced Sub On mode, the Subwoofer level control in the ‘Level Calibration’ menu will be inactive. This is because this setting is overwritten by the three appropriate Sub Trim settings from the ‘Advanced Sub’ menu.

OSD setup

On-Screen Display is available on the Composite and S-Video outputs only. (Not available on Component Video or HDMI.) Select the ‘OSD Setup’ menu, select ‘OSD Video’ and use the Left and Right arrows to select whether you would like the OSD video source to be Composite or S-Video:

OSD Setup Menu

TV Format : PAL

Background : Blue

OSD Video : Composite

Language : English

Custom installation (C.I.) use

	IR Emitter	The 340R features	an IR Emitter input	that allows
In		modulated IR remote control commands to be received
		electrically by the unit. These control commands are
		typically generated	by custom installation	(multi-room)

systems or remote IR receiver systems. An RS232 port is

also featured which allows the 340R to be controlled by C.I.

systems.RS232C

In addition the 340R features ‘direct’ IR/Control codes as well as toggle codes for many of their features to simplify programming custom installation systems. Special direct On/Off commands can be accessed on the supplied remote control for teaching into C.I. systems as follows:

1.Press and hold the Standby/On button on the remote control. The remote first generates it's standby (toggle) command. Keep the button held down, after 12 seconds an AV receiver ‘On’ command will be generated. If the button is kept held down for a further 12 seconds, an AV receiver ‘Off’ command is generated.

Repeat this procedure with the Mute, Sub On/Off, Stereo Mono and Tuner FM/AM buttons to send On/Off commands. The Tuner FM/AM button also provides unique FM and AM commands to allow switching to a specific band.

A full IR code table and RS232 protocol for this product is available on the Cambridge Audio website at: www.cambridge-audio.com

Return To Menu : [OSD]

The OSD can be shown either on a blue background or overlaid on the analog video. Select Background’ and use the Left and Right arrows to select between ‘Blue’ and ‘Video’ backgrounds.

The OSD can also be shown in several different languages. To change the OSD language highlight the ‘Language’ menu and use the Left and Right arrows to select between English, Dutch, French, German, Spanish, Italian, Norwegian, Swedish and Danish.

Press the OSD button again to exit and save the options.

Reset/Back-up memory

The 340R has a function that preserves the preset memory and other settings. In the event of a power failure, or if the power cord of the unit is disconnected from the mains outlet, the back-up memory will preserve the preset memory for approximately one week. If the power supply is interrupted for 7 days or longer, the memory settings will be erased.

If it is desired to reset all settings to their factory defaults (or in the unlikely event that the unit locks up due to an electrical discharge etc), with the unit on and out of Standby mode press and hold the DVD and

5.1Direct buttons on the front panel for three seconds:

DVD	Video 1	Video 2	Video 3	Tuner FM/AM Tape/MD/CDR			CD/Aux	5.1 Direct
Mode/Store
	Stereo	Dolby Digital/ Pro Logic II			DSP	Input
	Mode		DTS		Mode	Mode

‘RESET’ will appear briefly on the front panel display before returning to Standby mode.

20