Operating Instructions

Important Safety Instructions

b.. Never use oxygen, carbon dioxide,

1.

Disconnect the air

 

(Continued)

combustible gases or any bottled

 

 

supply from the tool

 

Service

gas as an air source for the tool.

 

 

 

to add lubricant..

 

Such gases are capable of explosion

 

 

 

a.. Tool service must be performed only

 

 

 

and serious injury to persons..

 

 

2.

Turn the tool so the air

 

by qualified repair personnel.

 

 

OIL

 

 

 

 

 

 

 

 

 

 

 

inlet is facing up.. Place

 

b.. When servicing a tool, use only

 

 

 

 

 

 

 

 

 

 

 

 

 

4-5 drops of 30 W non-

 

identical replacement parts. Use

 

 

 

 

 

 

 

Do not use any type of

O

CO2

 

 

detergent oil into air inlet..

 

 

 

 

 

 

only authorized parts.

 

 

 

 

 

reactive gases, including, but

 

 

 

Do not use detergent

 

c.. Use only the lubricants supplied

not limited to, oxygen and

 

 

 

 

 

 

 

 

 

oils, oil additives, or air- tool oils..

combustible gases, as a power source.

 

with the tool or specified by the

 

 

Air tool oils contain solvents which

Use filtered, lubricated, regulated

 

 

 

manufacturer.

 

 

 

compressed air only. Use of a reactive

 

will damage the tool's internal

 

 

Do not make any

gas instead of compressed air may

 

 

 

components..

 

modifications to

cause the tool to explode which will

 

3. After adding oil, run

 

the tool without first obtaining written

cause death or serious personal injury.

 

 

tool briefly.. Wipe off

 

approval from Campbell Hausfeld. Do

 

 

 

 

 

 

 

not use the tool if any shields or guards

 

 

 

 

 

 

any excess oil from the

 

are removed or altered. Do not use the

Use only a pressure-regulated

 

 

 

cap exhaust..

 

tool as a hammer. Personal injury or

 

 

 

 

 

compressed air source to limit 100 psi

 

 

 

tool damage may occur.

Recommended Hookup

 

Disconnect air

the air pressure supplied to

 

 

 

The illustration below shows the

the tool. The regulated pressure must

 

supply and release

not exceed 100 psi. If the regulator

 

 

recommended hookup for the tool..

tension from the pusher before

 

 

fails, the pressure delivered to the

 

 

1.

The air compressor

 

attempting to clear jams because

 

 

60 psi

tool must not exceed 200 psi. The tool

fasteners can be ejected from the front

 

must be able to

Min.

could explode which will cause death or

 

 

 

of the tool. Personal injury may occur.

serious personal injury.

 

 

 

 

maintain a minimum

100 psi

 

 

 

 

 

Max.

Air Source

 

 

 

 

 

 

of 60 psi when the

Save These Instructions

 

 

 

 

a.. Never connect to an air source that

 

Do Not Discard

 

 

 

tool is being used.. An inadequate air

 

 

 

 

supply can cause a loss of power and

is capable of exceeding 200 psi.

 

 

 

 

 

 

Operating Instructions

 

 

 

inconsistent driving..

 

Over pressurizing the tool is able

 

 

 

 

 

 

2. An oiler can be

 

to result in bursting, abnormal

Lubrication

 

 

 

 

 

 

 

 

used to provide oil

 

operation, breakage of the tool or

 

 

 

 

 

 

 

 

 

 

 

 

This tool requires lubrication before

 

 

circulation through

 

serious injury to persons.. Use only

 

 

 

using the tool for the first time and

 

 

 

the tool.. A filter can

 

clean, dry, regulated compressed air

 

 

 

 

before each use.. If an inline oiler is

 

 

 

be used to remove

 

at the rated pressure or within the

 

 

 

 

used, manual lubrication through the

 

 

liquid and solid impurities which can

rated pressure range as marked on

 

 

air inlet is not required on a daily basis..

 

rust or “gum up” internal parts of

the tool.. Always verify prior to using

 

 

 

 

 

 

 

the tool..

 

the tool that the air source has been

 

The work surface

 

 

 

adjusted to the rated air pressure or

 

can become

 

 

3.

Always use air supply hoses with

within the rated air-pressure range..

damaged by excessive lubrication.

 

 

 

a minimum working pressure

Proper lubrication is the owner’s

 

 

 

 

 

 

 

rating equal to or greater than the

 

responsibility. Failure to lubricate the

 

 

 

pressure from the power source if a

 

tool properly will dramatically shorten

 

 

the life of the tool and void your

 

 

 

regulator fails, or 150 psi, whichever

 

warranty.

 

 

 

 

 

 

 

Recommended Hookup

 

 

 

 

Regulator

 

 

 

 

Quick

 

 

 

Quick

Quick Plug

 

 

 

 

 

 

Coupler

 

 

 

 

 

Quick Plug

Coupler

(Optional)

(Optional)

 

 

 

Air Hose

LubricatorFilter

www.chpower.com

4