22Sp
Manual de Instrucciones y Lista de Piezas

RECORTES/ CORTE DEL AGUJERO

Los recortes se pueden hacer de dos
modos:
1.Haciendo un orificio inicial:
Para los cortes internos sin un corte
de entrada desde el borde, haga un
orificio inicial de 12 mm (1/2") o más
de diámetro con un taladro.
Introduzca la hoja en este orificio
ycomience a cortar.
2.Corte por penetración:
El corte por penetración es útil y ahorra
tiempo cuando se hacen aberturas
toscas en materiales blandos.
Nointente cortar por penetración
materiales duros tales como el acero.
CORTES POR PENETRACIÓN
1.Si el corte en bolsillo es de líneas
rectas, no se necesita un orificio
pretaladrado.
2.Incline la herramienta hacia adelante
sobre el borde delantero de la base
con la hoja ubicada apenas encima de
la superficie de la pieza(Figura 3).
3.Aplique presión sobre la herramienta
de modo que el borde delantero de
la base no se mueva cuando
encienda la herramienta y
suavemente baje la parte trasera de
la herramienta con lentitud.
4.Una vez que la sierra alcanza la
velocidad máxima, bájela
lentamente en la pieza de trabajo.
5.Mientras la hoja perfora la pieza,
baje lentamente la base de la
herramienta hacia la superficie de la
pieza de trabajo.
6.Mantenga ambas manos sobre la sierra
mientras esté cortando.
7.Complete el corte de manera normal.
8.Para 90° u otras esquinas en ángulo,
corte hasta la esquina luego retroceda
antes de redondear la esquina. Una
vez que haya cortado el bolsillo,
acérquese a la esquina desde la
dirección contraria y corte el ángulo.
CORTES DE BOLSILLO
Los cortes de bolsillo se hacen en el
medio de la pieza de trabajo cuando
no pueden cortarse desde un borde.
Se pueden comenzar con un orificio
pretaladrado o la sierra vertical puede
crear un punto de inicio (corte por
penetración).
Los cortes por penetración no se
recomiendan para materiales más
duros como el acero y no se deben
usar las hojas de calar para cortes
por penetración.
CORTES EN CÍRCULO
Una guía de corte en círculo puede
ayudarlo para cortar círculos. El corte
se debe preparar con un orificio
pretaladrado o un leve corte por
penetración próximo a la línea de
corte. Si usa una guía, asegúrese de
que cumpla con las instrucciones de la
sierra vertical y del fabricante.

CALADOS

Se pueden realizar trabajos complicados
con una sierra vertical usando una hoja
de calado. Asegúrese de que la hoja se
utilice de acuerdo a las instrucciones del
fabricante.

CORTE DE METALES

• Cuando corte piezas de trabajo de
metal, sujete el material con
abrazaderas y corte cerca del punto
de sujeción para reducir la posibilidad
de que se tuerza y la vibración.
• Si la hoja comienza a vibrar o a hacer
un ruido excesivo, reemplace la hoja
con una hoja para cortes en metal
que tenga dientes más finos.
• Para metales blandos, la hoja se
puede obstruir por lo tanto use una
hoja con dientes más gruesos.
• Los conductos, hierro en ángulo
otuberías se deben sujetar en una
prensa de tornillo y cortar lo más
cerca posible de la prensa.
• Los metales de hoja delgada deben
colocarse entre dos tablas de madera
o se deben colocar sobre tablones de
madera más gruesos, como madera
terciada y el diseño o diagramado se
debe poner encima. Esto permite
cortar el metal sin problemas y evita
el desgarro del material de metal.
• La hoja se puede lubricar para
facilitar el corte. Use una barra
decera para corte, si hubiese
disponible, y use aceite para corte
cuando corte acero.
• La porción expuesta de la barra de
lasierra se debe mantener limpia.
Elimine frecuentemente los restos
demetal usando un paño con aceite.
Después de usar, deseche
adecuadamente el paño con aceite
para evitar riesgos de incendio.
• Cuando corte metal sujete el material
con abrazaderas, continúe lentamente
y use las velocidades más bajas.
• No doble, tuerza ni fuerce la hoja. Si
la sierra salta o se balancea, use una
hoja con dientes más finos. Si la hoja
parece obstruida cuando corte
materiales blandos, use una hoja con
dientes más gruesos.
• Para un corte más fácil, lubrique la
hoja con cera para corte, si hubiese
disponible, o aceite para corte
cuando corte acero. El metal delgado
debe colocarse entre dos láminas de
madera o debe sujetarse firmemente
con abrazaderas a una sola pieza de
madera (la madera sobre el metal).
• Dibuje el diseño o las líneas de corte
en la parte superior de madera.
Cuando corte aluminio extruido o
hierro en ángulo, sujete el trabajo
con una prensa de tornillo y corte
cerca de las mordazas de la prensa.
• Cuando corte tuberías y el diámetro
sea mayor que la profundidad de la
hoja, corte la pared de la tubería y
luego introduzca la hoja en el corte
girando la tubería mientras corta.
No utilice el adaptador de aspiración
cuando corte metal. Las virutas de
metal estarán calientes y podrían
causar un incendio.

CORTE DE LÁMINAS

Mientras la hoja de la sierra corta en la
dirección ascendente, la superficie más
cercana a la placa de la zapata podría
astillarse.
1. Utilice una hoja de sierra con
dientes finos.
2. Corte desde la superficie posterior
de la pieza (lado terminado hacia
abajo).
3. Para minimizar el astillado, sujete
lapieza con madera de desecho
oaglomerado por ambos lados de la
pieza y corte con la pieza en el medio.

TERMINACIÓN DE BORDES

Para recortar los bordes o hacer ajustes
dimensionales, haga correr la hoja
apenas por los bordes de corte.

AJUSTE DEL CORTE DIAGONAL

Siempre asegúrese de que la
herramienta esté apagada. Desenchufe
la herramienta. El pie puede ajustarse
hasta 45°, soltando los pernos de ajuste
de corte diagonal, en la parte inferior
de la sierra.
Funcionamiento (Cont.)
6. NEVER hold piece being cut in your
hands or across your leg. It is
important to support the work
properly to minimize body exposure,
blade binding, or loss of control.
7. Wear ear protection when using the
tool for extended periods. Prolonged
exposure to high intensity noise can
cause hearing loss.
8. Make sure that all nails have been
pulled from workpiece before starting
cutting operation.
9. This saw is not designed to cut hollow
pipe. Perform cuts on approved
materials only.
10.Do not touch metal parts of saw while
cutting in blind areas. Blind spots like
walls and floors may contain live
electric wires.
11.Do not touch metal parts of saw or
blade immediately after use. Parts will
be hot and can cause serious burn.

POWER TOOL USE AND CARE

Do not
force the
power tool. Use the correct power tool
for your application. The correct power
tool will do the job better and safer at
the rate for which it was designed.
Do not
use the
power tool if the switch does not turn
it on and off. Any power tool that can-
not be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
Maintain
power
tools. Check for misalignment or bind-
ing of moving parts, breakage of parts
and any other condition that may affect
the power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by poor-
ly maintained power tools.
Keep
cutting
tools sharp and clean. Properly main-
tained cutting tools with sharp cutting
edges are less likely to bind and are
easier to control.
Use the
power
tool, accessories and tool bits etc. in
accordance with these instructions,
taking into account the working condi-
tions and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
1. This tool must NOT be modified or
used for any application other than
that for which it was designed.
2. Some wood contains preservatives
which can be toxic. Take extra care
to prevent inhalation and skin
contact when working with these
materials. Request and follow all
safety information available from
your material supplier.
3. Store tools out of reach of children
and other untrained persons. Tools
are dangerous in the hands of
untrained users.
4. Avoid cutting nails. Inspect
workpiece for any nails and remove
them before operation.
5. Do not cut hollow pipe.
6. Do not cut oversize workpiece.
7. Check for the proper clearance
beyond the workpiece before
cutting so that the blade will not
strike the floor, workbench, etc.
8. Make sure the blade is not
contacting the workpiece before
the switch is turned on.
9. Keep hands away from moving parts.
10.Do not leave the tool running. Operate
the tool only when hand-held.
11.Always switch off and wait for the
blade to come to a complete stop
before removing the blade from the
workpiece.
12.Do not touch the blade or the
workpiece immediately after
operation; they may be extremely
hot and could burn your skin.

CAUSES AND USER PREVENTION

OF KICKBACK:

Kickback is a sudden reaction to a
pinched, bound or misaligned saw
blade, causing an uncontrolled saw to
lift up and out of the workpiece
toward the operator.
When the blade is pinched or bound
tightly by the kerf, or cutting slot,
closing down, the blade stalls and the
motor reaction drives the unit rapidly
back toward the operator.
If the blade becomes twisted or
misaligned in the cut, the teeth at the
back edge of the blade can dig into
the top surface of the wood causing
the blade to climb out of the kerf and
jump back toward operator.
Kickback is the result of tool misuse
and/ or incorrect operating procedures
or conditions and can be avoided by
taking proper precautions as given
below:
1. Maintain a firm grip with both
hands on the saw and position your
body and arm to allow you to resist
kickback forces. Kickback forces can
be controlled by the operator, if
proper precautions are taken.
2. When blade is binding, or when
interrupting a cut for any reason,
release the trigger and hold the saw
motionless in the material until the
blade comes to a complete stop.
Never attempt to remove the saw
from the work or pull the saw
backward while the blade is in
motion or kickback may occur.
Investigate and take corrective
actions to eliminate the cause of
blade binding.
3. When restarting a saw in the
workpiece, center the saw blade in
the kerf, or cut, and check that saw
teeth are not engaged into the
material. If saw blade is binding, it
may walk up or kickback from the
workpiece as the saw is restarted.
4. Support large panels to minimize
the risk of blade pinching and
kickback. Large panels tend to sag
under their own weight. Supports
must be placed under the panel on
both sides, near the line of cut and
near the edge of the panel.
5. Do not use dull or damaged blades.
Unsharpened or improperly set
blades produce narrow kerf causing
excessive friction, blade binding and
kickback.
6. Blade depth and bevel adjusting
locking levers must be tight and
secure before making cut. If blade
adjustment shifts while cutting, it
may cause binding and kickback.
7. Use extra caution when making a
“Pocket Cut” into existing walls or
other blind areas. The protruding
blade may cut objects that can
cause kickback.
8. Be cautious of pitchy, knotty, wet or
warped stock. These are most likely
to create pinching conditions and
possible kickback.
3
www.chpower.com
DG460300CK
General Power Tool
Safety Warnings(Cont’d.)
Figura 3