Operating Instructions |
|
|
|
|
|
|
| CHN20102 | |||
User - Maintenance | TECHNICAL SERVICE |
|
| ASSEMBLY PROCEDURE FOR SEALS | |||||||
Instructions | Please call our Tool Hotline at | When repairing a tool, the internal | |||||||||
CLEARING A JAM FROM THE TOOL | parts must be cleaned and lubricated. | ||||||||||
1. | Disconnect the air | the operation or repair of this tool or | Parker | ||||||||
for additional copies of this manual. | used on all | ||||||||||
| supply from the | ||||||||||
|
|
|
|
| coated with | ||||||
| tool. | FASTENER AND REPLACEMENT |
| ||||||||
|
| A small amount of oil must be used on | |||||||||
|
| PARTS |
|
|
| ||||||
|
|
|
|
| all moving surfaces and pivots. After | ||||||
|
|
| Use only headless | ||||||||
2. | Remove all nails |
| reassembling, a few drops of 30W |
| |||||||
| micropins, 16 gauge. |
| |||||||||
| |||||||||||
| from the magazine | Tool performance, safety and durability | |||||||||
| be added through the air line before | ||||||||||
| (see Loading/ | could be reduced if improper fasteners | |||||||||
| are used. When ordering replacement | testing. |
|
|
| ||||||
| Unloading). Failure |
|
|
| |||||||
| parts or fasteners, specify by part |
|
|
|
|
|
| ||||
| to do so will cause |
| STORAGE |
|
|
| |||||
| number. |
|
|
|
|
|
| ||||
| the nails to eject from the front of |
|
|
|
|
|
| ||||
| TOOL REPAIR |
|
|
| The tool should be stored in a cool dry | ||||||
| the tool. |
|
|
| |||||||
|
|
|
| place. |
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
3. | Undo latch by | Only qualified personnel should repair |
|
|
|
| |||||
|
|
|
|
| |||||||
| pulling out | the tool and they should use genuine |
|
|
|
|
| ||||
| and down. The | Campbell Hausfeld replacement parts |
|
|
|
|
| ||||
| wire latch will | and accessories, or parts and accessories |
|
|
|
|
| ||||
| disengage from | which perform equivalently. |
|
|
|
|
|
| |||
| the hooks on the nose. |
|
|
|
|
|
|
|
|
| |
4. | The door can |
|
|
|
|
|
|
|
|
| |
| now be rotated, |
|
|
|
|
|
|
|
|
| |
| exposing the |
|
|
|
|
|
|
|
|
| |
| jammed fastener. |
|
|
|
|
|
|
|
|
| |
5. | Remove the |
|
|
|
|
|
|
|
|
| |
| jammed fastener, |
|
|
|
|
|
|
|
|
| |
| using pliers or |
|
|
|
|
|
|
|
|
| |
| a screwdriver if |
|
|
|
|
|
|
|
|
| |
| required. | Fasteners |
|
|
|
|
|
|
|
| |
6. | Rotate door back |
|
|
|
|
|
|
|
| ||
The following Campbell Hausfeld finishing nails are available at local retail stores. | |||||||||||
| into the closed | ||||||||||
| If you need help locating any item, call customer service at |
| |||||||||
| position. |
| |||||||||
| Campbell Hausfeld nails meet or exceed ASTM Standard F1667. |
|
| ||||||||
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| Nails | Nails | |
7. | Extend the wire |
|
| Shank |
|
|
|
| Per | Per | |
Model | Length | Gauge | Finish | Head | Collation | Stick | Box | ||||
| latch and place | ||||||||||
|
|
|
|
|
|
|
|
|
| ||
| over the hooks on | FB005060 | 2 | 16 | Galvanized | Brad | Adhesive | 50 | 2500 | ||
| the nose. |
| inch | Gauge |
|
|
|
|
|
| |
8. | Close the latch by | FB160025 | 1 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | ||
| pushing the latch |
| inch | Gauge |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
| up and in until the | FB160040 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | |||
| latch snaps into |
| inch | Gauge |
|
|
|
|
|
| |
| place. | FB160065 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | |||
9. | Make sure the |
| inch | Gauge |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
| trigger and work | Interchange Information |
|
|
|
|
|
| |||
| contact element |
|
|
|
|
|
| ||||
| (WCE) move freely | Nails used in the Campbell Hausfeld CHN201 Finishing Nailer will also work in | |||||||||
| up and down | Hitachi NT65A, Paslode | |||||||||
| without sticking or binding. | Cable FN200 and FN250. |
|
|
|
|
|
| |||
www.chpower.com | 6 |