Operating Instructions

 

 

 

 

 

Model JB004250

Operating The Nailer

4.

Reconnect air

 

 

3.

Insert a stick

 

supply to the

 

 

 

of Campbell

(Continued)

 

 

 

 

 

nailer.

 

 

 

Hausfeld nails

Sequential Trip Safety

 

 

 

 

 

or equivalent

 

 

 

 

 

(see

Mechanism

 

 

 

 

 

"Fasteners"

The tool is equipped with a sequential

5.

Depress the Work

 

 

section) into

 

 

the magazine. Make sure the

trip safety mechanism. When the

 

 

 

Contact Element

 

 

 

pointed ends of the nails are resting

operator depresses the Work Contact

 

 

 

 

 

(WCE) against the

 

 

on the bottom ledge of the

Element (WCE) against the work

 

 

 

 

work surface

 

 

 

magazine when loading. Make sure

surface and then pulls the trigger, a

 

 

 

 

 

 

 

 

the nails are not dirty or damaged.

fastener will be driven.

 

without pulling

 

 

 

 

 

 

4.

Push the

OPERATING A SEQUENTIAL TRIP

 

the trigger. The

 

 

 

nailer MUST NOT

 

 

magazine

TOOL

 

OPERATE. Do not use the tool if it

 

cover

1.

Release

 

 

forward

 

operates without pulling the trigger.

 

 

trigger and

 

 

until the

 

 

Personal injury may result.

 

 

 

place nose of

 

 

 

latch catches.

 

6.

Remove nailer

 

 

 

 

tool against

 

 

 

 

 

work surface.

 

from work

 

 

5. Always unload all fasteners before

 

 

 

surface. The

 

 

 

 

 

 

 

 

removing tool from service.

 

 

 

Work Contact

 

 

 

2.

Depress the

 

 

 

 

Unloading is the reverse of loading,

 

Work contact

 

Element (WCE)

 

 

 

except always disconnect the air

 

element (WCE)

 

must return to

 

 

 

supply before unloading.

 

against the

 

its original

 

 

ADJUSTING THE NAIL PENETRATION

 

work surface

 

 

 

 

 

down position. Pull the trigger. The

The nailer is equipped with an

 

and pull the

 

 

 

nailer MUST NOT OPERATE. Do not

 

trigger to

 

adjustable depth of drive feature. This

 

 

use the tool if it operates while lifted

 

drive a fastener.

 

allows the user to determine how deep a

3.

Release the

 

from the work surface. Personal

fastener will be driven into the work

 

trigger and

 

injury may result.

 

 

surface.

 

lift the tool

7.

Pull the

1

2

1.

Adjust operating pressure so nails

 

from the work

 

trigger and

 

are driven consistently. Do not

 

surface after

 

 

 

 

 

 

depress the

 

 

 

exceed 100 psi.

 

each fastener

 

 

 

 

 

 

Work

 

 

2. To drive the nail shallower, turn the

 

is driven.

 

 

 

CHECKING THE WORK CONTACT

 

Contact

 

 

 

wheel (C) to right to the extent

 

Element

 

 

 

desired.

ELEMENT (WCE)

 

 

 

 

 

(WCE) against the work surface. The

 

 

 

 

 

 

 

 

Check the

 

nailer MUST NOT OPERATE.

 

 

 

 

opertion

8.

Depress

 

 

 

 

of the Work Contact Element (WCE) trip

1

2

 

 

 

the Work

 

 

mechanism before each use. The WCE

 

 

 

 

 

must move freely without binding

 

Contact

 

 

 

 

through its entire travel distance. The

 

Element

 

 

 

 

WCE spring must return the WCE to its

 

(WCE)

 

 

 

(C)

fully extended position after being

 

 

 

 

 

against

 

 

 

 

depressed. Do not operate the nailer if

 

 

 

 

 

the WCE trip mechanism is not operating

 

work surface. Pull the trigger. The

 

 

properly. Personal injury may occur.

 

nailer MUST OPERATE.

 

 

 

1.

Disconnect the

LOADING/UNLOADING THE NAILER

 

 

 

air supply from

 

 

 

the nailer.

1.

Always connect

 

 

3. To sink a nail deeper, turn the wheel

 

 

 

the tool to the

 

 

 

 

 

 

 

 

(C) to left to the extent desired.

 

 

 

air supply

 

 

 

 

 

 

 

 

4. Make sure trigger and work contact

 

 

 

before loading

 

 

 

 

 

 

 

 

element (WCE) move freely up and

 

 

 

fasteners.

 

 

 

 

 

 

 

 

 

down without binding or sticking

2. Remove all nails from the magazine

 

 

 

 

 

 

 

 

 

 

after each adjustment.

 

(see Loading/ Unloading The

2.

Press down on

 

 

 

 

 

 

 

 

 

Nailer).

 

 

 

 

 

 

latch and pull

 

 

 

 

3.

Make sure the

 

 

 

 

 

 

back on the

 

 

 

 

 

trigger and work

 

magazine

 

 

 

 

 

contact element

 

cover.

 

 

 

 

 

(WCE) move freely

 

 

 

 

 

 

 

 

 

 

 

 

 

up and down

 

 

 

 

 

 

 

without sticking or

 

 

 

 

 

 

 

binding.

 

 

 

 

 

 

www.chpower.com

 

 

 

 

 

 

4