Campbell Hausfeld NB0040 operating instructions Fasteners and Replacement Parts, Nailer Repair

0 200

0 200

70 100

70 100

Operating Instructions Model NB0040

6.	Remove nailer
	from work sur-
	face. The Work
	Contact Element
	(WCE) must
	return to its
	original down
	position. Pull the trigger. The nailer
	MUST NOT OPERATE. Do not use the
	tool if it operates while lifted from
	the work surface. Personal injury may
	result.
7. Pull the trig-		1	2
	ger and
	depress the
	Work
	Contact
	Element
	(WCE) against the work surface. The
	nailer MUST OPERATE.
8.	Depress the	1	2
	Work
	Contact
	Element
	(WCE)
	against
	work surface. Pull the trigger. The
	nailer MUST
	OPERATE.
LOADING/UNLOADING THE NAILER
1.	Always connect
	the tool to the
	air supply before
	loading fasten-
	ers.
2.	Press down on
	latch and pull
	back on the
	magazine
	cover.
3. Insert a stick of
	Campbell
	Hausfeld nails
	or equivalent
	(see
	"Fasteners" sec-
	tion) into the magazine. Make sure
	the pointed ends of the nails are
	resting on the bottom ledge of the
	magazine when loading. Make sure
	the nails are not dirty or damaged.
4.	Push the
	magazine
	cover for-
	ward until
	the latch
	catches.

5.Always unload all fasteners before removing tool from service.

Unloading is the reverse of loading, except always disconnect the air supply before unloading.

ADJUSTING THE NAIL PENETRATION

1.Regulate the air pressure to 70 psi at the nailer.

2.Connect the

air supply and test for penetration by driving

nails into a

sample piece of wood. If the nails do not achieve the desired penetra- tion, adjust the air pressure to a higher setting until the desired pen- etration is achieved. Do not exceed 110 psi at the nailer or durability of the nailer will be reduced.

ADJUSTING THE DIRECTION OF THE EXHAUST

The NB0040 is
equipped with an
adjustable direc-
tion exhaust
deflector. This is	Rotate
intended to allow

the user to change the direction of the exhaust. Simply twist the deflector to any direction desired.

CLEARING A JAM FROM THE NAILER

1.Disconnect the air supply from

the nailer.

2. Remove all nails from the magazine (see "Loading/ Unloading The Nailer"). Failure to do

so will cause the nails to eject from the front of the nailer.

3. Undo latch by pulling out

and down. The wire latch will disengage

from the hooks on the nose.

4. The door can now be rotat- ed exposing the jammed fastener.

5. Remove the jammed fas- tener, using pliers or a screwdriver if required.

6. Rotate door back into the closed position.

7. Extend the wire latch and place over the hooks on the nose.

8. Close the latch by pushing the latch up and in until the latch snaps into place.

9.	Make sure the
	trigger and work
	contact element
	(WCE) move
	freely up and
	down without
	sticking or binding.

TECHNICAL SUPPORT

Please call our Nailer hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this nailer. If calling from Ohio or outside of the continental United States, please call, 1-513-367-1182.

Fasteners and Replacement Parts

Use only genuine

Campbell Hausfeld

18 gauge fasteners (or equivalent - See "Fastener Interchange Information"). Use only genuine Campbell Hausfeld replace- ment parts. Never substitute parts. Do not use modified parts or parts which will not provide equivalent performance to the original equipment. Tool perfor- mance, safety, and durability could be reduced. When ordering parts or fasten- ers, specify by part number.

Nailer Repair

Nailer repairs must be performed by a qualified service person or an authorized service center

Assembly Procedure For Seals

When repairing a nailer, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coat- ed with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non- detergent oil or equivalent, must be added through the air line before testing.

www.campbellhausfeld.com

4