Operating Instructions and Parts Manual
Troubleshooting Chart - Gasoline Powered Pressure Washers Only
| Symptom | Possible Cause(s) | Corrective Action(s) | ||
|
|
|
|
|
|
| Engine will not start or is | 1. | No gasoline in fuel tank or carburetor | 1. | Fill the tank with gasoline,open fuel shut off |
| hard to start |
|
|
| valve. Check fuel line and carburetor |
|
| 2. | Low oil | 2. | Check oil level. Fill if necessary |
|
| 3. | Start/Stop switch in stop position | 3. | Move switch to start position |
|
| 4. | Water in gasoline or old fuel | 4. | Drain fuel tank and carburetor. Use new fuel and |
|
|
|
|
| dry spark plug |
|
| 5. | Dirty air cleaner filter | 5. | Remove and clean or replace |
|
| 6. | Spark plug dirty, wrong gap or wrong type | 6. | Clean, adjust the gap, or replace |
|
| 7. | Spray gun closed | 7. | Trigger spray gun |
|
| 8. | Other causes | 8. | See engine owner’s manual |
|
|
|
|
|
|
| Engine misses or lacks | 1. | Partially plugged air cleaner filter | 1. | Remove and clean or replace |
| power | 2. | Spark plug dirty, wrong gap or wrong type | 2. | Clean, adjust the gap, or replace |
|
|
|
|
|
|
|
| 1. | Worn or wrong size tip | 1. | Replace with tip of proper size |
| Low pressure and/or pump | 2. | Inlet filter on pump clogged | 2. | Clean. Check more frequently |
| runs rough | 3. | Worn water seals, abrasives in water, or natural | 3. | Check filter. Replace water seals. See service center |
|
|
| wear |
|
|
|
| 4. | Fouled or dirty inlet or discharge valves | 4. | Clean inlet and discharge valve assemblies. Check |
|
|
|
|
| filter |
|
| 5. | Restricted inlet | 5. | Check garden hose, may be collapsed or kinked. |
|
|
|
|
| Check inlet water flow |
|
| 6. | Worn inlet or discharge valves | 6. | Replace worn valves |
|
| 7. | Leaking high pressure hose | 7. | Replace high pressure hose |
|
| 8. | Pump drawing in air | 8. | Ensure hoses and fittings are tight |
|
| 9. | Unloader valve seat faulty or worn | 9. | Check and replace |
|
|
|
| ||
| Water leakage from under | Worn water seals | Install new water seals. See service center | ||
| pump manifold |
|
|
|
|
|
|
|
|
|
|
| Water in pump crankcase | 1. | Humid air condensing inside crankcase | 1. | Change oil as specified in maintenance schedule |
| (milky oil) | 2. | Oil seals leaking | 2. | Install new oil seals. See service center |
|
|
|
|
|
|
| Frequent or premature | 1. | Scored damaged or worn plungers | 1. | Install new plungers. See service center |
| failure of the pump water | 2. | Abrasive material in the fluid | 2. | Install proper filtration on pump inlet plumbing |
| seals | 3. | Inlet water temperature too high | 3. | Check water temperature; may not exceed 100o F. |
|
| 4. | Overpressurizing pump | 4. | Do not modify any factory set adjustments. |
|
| 5. | Excessive pressure due to partially plugged | 5. | Clean or replace tip. |
|
|
| or damaged tip |
|
|
|
| 6. | Pump running too long without spraying | 6. | Never run pump more than 2 minutes without |
|
|
|
|
| spraying |
|
| 7. | Pump running dry | 7. | Do not run pump without water |
Strong surging at the inlet and low pressure
Foreign particles in the inlet or discharge valve or Clean or replace valves. See service center worn inlet and/or discharge valves
| Oil leakage between the | Worn oil seals and/or | Replace oil seals and/or |
| ||
| engine and the pump |
|
|
|
|
|
|
|
|
|
|
|
|
| Fluctuating pressure | 1. | Valve worn, dirty or stuck | 1. | Check and replace |
|
|
| 2. | Pump drawing in air | 2. | Ensure hoses and fittings are tight. Purge air from |
|
|
|
|
|
| garden hose |
|
|
| 3. | Tip clogged | 3. | Check or replace |
|
|
|
|
|
|
|
|
| Pressure drops after period | 1. | Worn pump water seals | 1. | Check and replace |
|
| of normal use | 2. | Nozzle worn | 2. | Check and replace |
|
|
| 3. | Valve worn, dirty or stuck | 3. | Check, clean or replace |
|
|
| 4. | Unloader valve seat worn or dirty | 4. | Check, clean or replace |
|
|
| 5. | Nozzle in low psi position | 5. | Pull back nozzle to high pressure position |
|
www.chpower.com
12
