1 Unpack the MultiPASS C545
2 Set Up the MultiPASS
Place the main unit of the MultiPASS on a level surface with plenty of room to work.
1Carefully remove all items from the box.
3Open the document tray.
1Attach the sending document support.
MultiPASS, PC Modem and Telephone
Remove these items from the documentation package: this Quick Start Guide, the MultiPASS C545 Installer CD packet, MultiPASS C545 User's Manual, Registration card, and Warranty card.
Remove the protective sheet covering the operation panel.
Fit the tabs on the sending |
|
document support into the | ADF |
slots above the ADF. |
|
Make sure the |
|
Wall Jack
Telephone
PC
Remove these hardware items from the top tray:
TELEPHONE |
| |
LINE | POWER | |
SENDING DOCUMENT | ||
CORD | ||
SUPPORT | ||
| ||
| ||
CABLE |
| |
BJ CARTRIDGE | ||
STORAGE BOX | ||
| ||
EXTRA |
| |
BLACK BJ TANK |
|
Lift out the MultiPASS unit from the bottom.
Important! Save the box and shipping materials. You may need them later if you have to transport the MultiPASS.
2Remove all pieces of shipping tape.
Remove all pieces of shipping tape from the outside of the printer. Be sure to remove the tape from the back of the printer also.
Remove the protective plastic piece from the sheet feeder.
PROTECTIVE
PLASTIC
AUTOMATIC DOCUMENT FEEDER (ADF)
4Open the operation panel.
Use both hands to grip the operation panel, and gently pull it toward you until it opens partially.
Remove the soft styrofoam sheet from the unit's Automatic Document Feeder (ADF).
Press the operation panel closed until it clicks into place.
5Open the printer cover.
Check for any tape or shipping material inside the unit and remove it.
| |
PRINTER | (SHEET FEEDER) – |
COVER | holds paper for |
| printing or receiving faxes |
AUTOMATIC DOCUMENT FEEDER (ADF) –
support curves |
toward the back |
of the unit. |
2Connect the phone line.
The MultiPASS unit has three telephone jacks (located on the left side of the unit) that will accept standard line connections.
| Use the bottom L jack to connect the wall |
Jacks on | jack to the MultiPASS with the supplied |
MultiPASS | line cord (unless connected with Caller ID). |
| |
| The other two jacks are |
| to connect other devices to the MultiPASS |
L | and your telephone service. Select from the |
options in the diagram below to configure | |
| your telephone device to work in |
| conjunction with your MultiPASS. |
If you have only one telephone line and plan to use the MultiPASS for receiving both faxes and voice calls, you must attach a telephone and/or answering machine to the unit.
If you use Caller ID with any of these configurations, place the Caller ID device between the MultiPASS and the wall jack.
Recommended Device Connections |
| Receive Modes |
MultiPASS Only |
| Fax Only |
|
| or DRPD |
Wall Jack |
|
|
MultiPASS and Telephone |
| Fax/Tel, DRPD, |
|
| or Manual |
| Telephone |
|
Wall Jack |
|
|
MultiPASS and Answering Machine |
| Ans.Machine |
Wall Jack | Answering |
|
Machine |
| |
|
| |
MultiPASS, Answering Machine and Telephone | Ans.Machine | |
Wall Jack | Answering | Telephone |
Machine |
| |
|
| |
MultiPASS and PC Modem |
| Fax Only |
| PC | or DRPD |
|
| |
MultiPASS, PC Modem and
Answering Machine
Answering
Machine
Wall Jack
PC
MultiPASS, PC Modem, Answering
Machine and Telephone
Telephone
Wall Jack
PC
3Connect the USB—to—Parallel cable and power cord.
Make sure the computer is turned off.
Connect the
computer.
Power Cord | |
(to outlet) | (to computer) |
Connect the power cord to the MultiPASS and to a wall outlet. The MultiPASS has no power switch. The power is on as long as the system is plugged in.
The MultiPASS is equipped with a
Caution feature. Do not defeat the safety purpose of this plug. Make sure the
located near the MultiPASS and is easily accessible.
Note that tape may not be in the exact locations shown.
PAGE 2 (BACKS COVER/1)
holds documents to be faxed, copied or scanned
Wall Jack
PAGE 3 (BACKS 6) | CANON/MPC545 Q.S.G: Pages 2 & 3 | - File: |
| Wendi Swanlund | Correx> August 19 '99 |
