CarAlarms.com P90-NG1 manual Locating Your GAS Fireplace, Heatwave, Optional Heat Release KIT

INSTALLATION

LOCATING YOUR

GAS FIREPLACE

1)When selecting a location for your fi replace, ensure that the clearances outlined on this page are met.

2)Provide adequate clearances for servicing.

3)The appliance must be installed on a fl at, solid, continuous surface (e.g. wood, metal, concrete).This may be the floor, or raised up on a platform to enhance its visual impact. If the appliance is going to be installed on carpeting, combustible linoleum tile or other combustible material other than wood fl ooring, the appliance must be installed on a metal or wood panel extending the full width and depth of the appliance.

4)The P90 Direct Vent Gas Fireplace can be installed in a recessed position or framed out into the room as in A, B, C, D. See Diagram 1.

A) Flat on Wall

B) Flat on Wall Corner

C) Recessed into

Wall/Alcove

D)Corner

Diagram 1

5)This appliance is Listed for bedroom installations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

6)The P90 Direct Vent Gas Fireplace is approved for alcove installations, which meet the clearances listed on this page.

7)We recommend that you plan your instal- lation on paper using exact measurements for clearances and fl oor protection before actually installing this appliance. Have a qualified inspector, dealer, or installer review your plans before installation.

Note: For vent terminations see the "Exterior Vent Termination Locations" section.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1)Ensure that structural members are not cut or weakened during installation.

2)Ensure proper grounding using the #8 ground lug provided. See the "Wiring Diagram" section.

HEATWAVE

DUCT SYSTEM OPTIONAL KIT #946-556

The HeatWave Air Duct Kit increases the effectiveness of your fi replace by dispersing warmairfromthefireplacetoremotelocationsin the same room or other rooms in your home.

Up to two kits may be installed on the fi replace. Please Note: Only 1 HeatWave kit may be operated at one time. This includes the internal blower option as well.

OPTIONAL

HEAT RELEASE KIT

#946-570

The Heat Release Kit expels warm air from the fi replace to the outside of the building, allowing the fi replace to be operated with less heat entering the room. The kit may be used on either the left or right side.

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fireplace and vent system be installed only in accordance with these instructions.

Clearance to Combustibles from:
Back	0"	(0mm)
Side	0"	(0mm)
Floor	0"	(0mm)

NOTE: The minimum floor clearance must be maintained from the top surface of the carpeting, tile, etc.

Side Wall Clearance	6-1/2" (165mm)
Horizontal Vent Clearances
Top	2-1/2" (64mm)
Side	1-1/2" (38mm)
Bottom	1-1/2" (38mm)
Vertical Vent Clearances	1-1/4" (32mm)
Alcove Clearances**:
Max. Depth	36"	(914mm)
Min. Width	48"	1219mm)
Min. Height	72"	1829mm)

* see mantle clearance instructions

(Refer to the "Combustible Mantels" section).

WARNING:

Fire hazard is an extreme risk

if these clearances are not

adhered to.

Clearances for HeatWave and

Heat Release Kit

Heat Release Kit

The HeatWave Duct Kit and the Heat Release Kit have different clearance and framing requirements, check the HeatWave and Heat Release manual for details.

Excalibur® P90 Zero Clearance Direct Vent Gas Fireplace 7