Power Cord | Sample Furnace Circuit Board | |
to EAC Terminals | ||
|
Use cable connector to secure
power cord to cabinet | Power Supply Connector |
Power Supply Connector
Power Supply
Use wire ties to secure power cord to power supply enclosure
Alternate Power Cord
Power Cord
W2 | OFF | OFF | 12 ON |
| LHT |
|
|
Y1 | DLY |
| 3 |
|
| ||
DHUM |
|
|
|
G |
|
|
|
24V |
|
|
| TEST/TWIN |
|
| ||||
|
|
|
| |||||||
COMWW1 |
|
|
|
| HUM | PLT |
| ACRDJ | ||
|
|
|
|
|
| |||||
Y/Y2 |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
R |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FUSE |
|
|
|
| |||
|
|
|
| T |
|
|
|
|
|
|
| S AT |
|
|
|
|
| ||||
ED |
|
|
| |||||||
| S |
|
|
|
|
| ||||
L |
|
|
|
|
|
| ||||
| E |
| C |
|
|
| PL1 | |||
|
|
| DO |
|
|
|
| |||
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| BLW |
|
|
|
| 1 |
| |||
BHI/LOR |
|
|
|
| BHT/CLR | |||||
HI HEAT |
|
|
|
|
|
|
| |||
LO |
|
| COOL |
|
| |||||
HEAT |
|
Use terminals to connect the power cord wires to the furnace
|
| PL3 |
|
|
| 1 |
|
BLWR |
|
|
|
IDR | HSIR | IDM | IHI/LOR |
L1 | 1 PL2 |
|
|
HSI | HI LO |
| |
|
|
GAPA
A06030
Fig. 7 - Infinityt Air Purifier Electrical Connections
START-UP AND OPERATION
Step 1—Checking Air Purifier Operation
!WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury or death.
Before installing or servicing system, always turn off main power to system. There may be more than one (1) disconnect switch.
a.Attach the Infinityt Air Purifier door to the cabinet. A magnet in the door (see Fig. 9) is used to activate a safe- ty switch in the power supply when the door is installed. The power supply will not energize the air purifier un- less the safety switch is activated.
b.Turn the HVAC system power on and adjust the thermostat or Infinityt System Control to activate the system fan.
c.Turn the Infinityt Air Purifier power switch to on position.
d.The power indicator light above the Air Purifier power switch should illuminiate (see Fig. 8).
e.Check to ensure the light goes off when the Infinityt Air Purifier power switch is set to off, when the blower goes off, or when the HVAC system power is turned off.
Step 2—Infinity Control
a.When the Infinityt Air Purifier is used with an Infinity Control, the Infinity Control can be configured to remind the homeowner when it is time to change the Infinityt Air Purifier cartridge. This maintenance reminder can be based on either the TrueSenset dirty filter algorithm or time. The installer should use their discretion to select the most appropriate option based on the initial system static pressure.
Step 3—Maximizing Performance
a.Maximum air purification performance is obtained when the furnace blower is set for continuous operation on the thermostat or Infinity Control.
Power Indicator
A06052
Fig. 8 - Power Indicator
MAINTENANCE
The Infinityt Air Purifier is designed to require no cleaning. Maintenance is limited to the replacement of the air purification cartridge. Frequency of air purifier cartridge replacement may vary depending on ductwork design and local environmental conditions.
To replace the air purifier cartridge, complete the following steps:
Step
!WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury or death.
Before installing or servicing system, always turn off main power to system. There may be more than one (1) disconnect switch.
6