Carrier 58MSA instruction manual A99123

15

11NO PREVIOUS FAULT - Faults are erased after 48 hrs or whenever power (115v or 24v) is interrupted. Run system through a heating or cooling cycle to check system.

12BLOWER ON AFTER POWER UP (115V OR 24V) - Normal operation. Blower will run for 90 sec when furnace power is interrupted during a call for heat, R-W closed.

13LIMIT OR FLAME ROLLOUT SWITCH LOCKOUT -

Limit switch was open longer than 3 minutes. Auto-reset will occur after 3 hrs. Flame rollout switch requires manual reset.

See No. 33

14IGNITION LOCKOUT - System failed to ignite gas and prove flame in 4 attempts. Control will auto-reset in 3 hrs.

See No. 34

21 GAS HEATING LOCKOUT -
Turn off power and wait 5
minutes to retry.
Check for:
• Stuck closed gas valve relay
	on control.
• Miswire or short to gas valve
	wire.
22 ABNORMAL FLAME PROVING
SIGNAL - Flame was sensed
while gas valve was
de-energized. Inducer will run
until fault is cleared.
Check for:
• Stuck open gas valve solenoid
	or leak.
•	Defective control center.
23 PRESSURE SWITCH WILL
NOT OPEN - Check for:
•	Disconnected or obstructed
	pressure tubing.
•	Defective pressure switch.

31PRESSURE SWITCH WILL NOT CLOSE OR REOPEN - If open longer than 5 minutes, inducer shuts off for 15 minutes before retry.

Check for:

•Proper vent sizing or pitch or sag.

•Vent restrictions or high winds.

•Defective inducer motor.

•Low line voltage (115v).

•Motor start capacitor.

•Low inlet gas pressure.

•Defective pressure switch or connections. If it opens after trial for ignition period, blower will come on for 90 sec recycle delay.

•Inadequate combustion air.

33 LIMIT OR FLAME ROLLOUT
SWITCH IS OPEN - If
limit switch is open longer than 3
minutes, code changes to No. 13.
Check for:
•	Blower motor failure.
•	Motor start capacitor.
• Open flame rollout switch,
	manual reset.
•	Inadequate combustion air
	supply (flame rollout switch
	only).
•	Dirty filter.
• Defective limit switch or
	connections.
•	Loose blower wheel.
34 IGNITION PROVING FAILURE -
If flame is not sensed during the
trial for ignition period, the control
will repeat the ignition sequence
3 more times before going into
lockout, No. 14.
If flame signal is lost after trial for
ignition period, blower will come
on for 90-sec recycle delay.
Check for the following items first
before proceding to the next step.
• Gas valve turned off.
• Manual shut-off valve.		NO
•	Green wire must be connected
	to furnace sheet metal.
To determine whether the
problem is in the gas valve,
ignitor, or flame sensor, the
system can be operated in the

Unplug ignitor harness from control
center and inititate another
component test sequence. Check	NO
for 115v between pins 1 and 2 on
the control center. Was 115v present
for the 17-sec period?
YES
Check for continuity in the harness
and ignitor. Replace defective
component.

Reconnect the R thermostat lead
and set thermostat to call for heat.	NO
Connect voltmeter across gas valve
connections. Does gas valve
receive 24v?
YES

Does gas valve open and allow gas	NO
to flow?
YES
Do main burners ignite?	NO
YES
Do main burners stay on?	NO
YES
Allow blower to come on and repeat
test to check for intermittent
operation.

Replace control center.

Check connections. If OK, replace control center.

Check that all gas valves are turned on. Replace valve.

Check for:

•Inadequate flame carryover on rough ignition.

• Low inlet gas pressure.

Repeat call for heat and check flame sensor current during trial for ignition NO period. Is the DC microamps

below 0.5?

YES

Check connections and retry. If current is near typical value and control will not stay on, replace control center.

Clean flame sensor with fine sandpaper and recheck current.

Current is nominally 4.0 to 6.0 microamps.

Is current near typical value? NO Replace electrode.

24 LOW-VOLTAGE FUSE IS

OPEN - Check for:

• Short in low-voltage wiring

including thermostat leads

shorting to ductwork or

furnace cabinet. Disconnect

thermostat leads to isolate

short circuit.

component test mode to check

the ignitor. First, remove the

R thermostat connection from the

control center and initiate the

component test sequence. Does

the ignitor glow orange/white hot

by the end of the 17-sec warm-up

period?

YES

YES

Will main burner ignite and stay on?

YES

Fixed.

NO

Replace control center.

A99123