Carrier TCSNHP01, TCSNAC01 Option 10 O Reversing Valve on with Heat or Cool Selection

TCSN

3.Press MODE button once. The SET icon will come on. The display now shows Option 07 setting.

4.Use up and down buttons to move between available Option 07 choices of ON or OF. Factory default is OF.

5.Press MODE button again to return to Option 07. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

OPTION 10 - O (REVERSING VALVE) ON WITH HEAT OR COOL SELECTION

This selection is only available on HP model thermostats when HP is selected via Option 05. This selection determines whether the reversing valve is energized in the heating or cooling mode. Factory default is C, energized in cooling. Use up and down buttons to change between H and C.

To Select:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 10.

3.Press MODE button once. The SET icon will come on. The isplay now shows Option 10 setting.

4.Use up and down buttons to move between available Option 10 choices of H (heat) or C (cool). Factory default is C.

5.Press MODE button again to return to Option 10. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

OPTION 13 - ROOM TEMPERATURE OFFSET

This option allows calibration (or deliberate miscalibration) of room temperature sensor. There are various reasons why the home owner may want to have displayed temperature adjusted to a higher or lower value. The selected number is the number of degrees, plus or minus, which will be added to the actual temperature. The number can range between -5 and +5. Factory default is 0. This adjusted value will be used as actual temperature for both display and control action. For example, if 2 is selected, 72_F/22_C actual will read 74_F/23_C. If setpoint is 72_F/22_C, the room will control to an actual value of 70_F/21_C which will be displayed and acted upon as if it were 72_F/22_C. The effect is that a positive number selection will make the room temperature lower and vice versa.

To Select:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 13. The SET icon should be off.

3.Press MODE button once. The SET icon will come on. The display now shows Option 13 setting.

4.Use up and down buttons to move between available Option 13 choices of -5 through +5 in 1_ steps. Factory default is 0.

5.Press MODE button again to return to Option 13. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

OPTION 15 - AUTO MODE ON/OFF SELECTION

This options allows the installer to enable or disable AUTO mode (automatic changeover between heat and cool). When disabled, AUTO icon does not appear when successive presses of MODE button are used to move between OFF, HEAT, and EHEAT (in heat pump systems). Factory default is ON (AUTO mode enabled).

To Select:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 15. The SET icon should be off.

3.Press MODE button once. The SET icon will come on. The display now shows Option 15 setting.

4.Use up and down buttons to move between available Option 15 choices of ON or OF. Factory default is ON.

5.Press MODE button again to return to Option 15. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

OPTION 18 - BACKLIGHT CONFIGURATION

This function is only available when the thermostat is operating from full power via R and C. It is not available when the thermostat operates from batteries. In OF (off) mode, this function is disabled. The thermostat backlight will normally be off. It turns on with any button press and stays on for 10 seconds in between button presses. In ON mode, this function is enabled. The thermostat backlight will normally be on and dim in appearance. The backlight becomes brighter with any button press and remains bright for 10 seconds. Factory default is OF.

To Select:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 18. The SET icon should be off.

3.Press MODE button once. The SET icon will come on. The display now shows Option 18 setting.

4.Use up and down buttons to move between available Option 18 choices of ON or OF. Factory default is OF.

5.Press MODE button again to return to Option 18. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

OPTION 19 - EQUIPMENT PRESENT

This selection informs the thermostat of the heat, cool, and fan capabilities of the installed equipment. Select number 2, 3, or 4. Default is 4.

For equipment with heat and cool capability and fan selection, choose 4.

For equipment with only heat or cool, but with fan selection, choose 3.

For equipment with only heat or cool and no fan selection, choose 2.

To Select:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 19. The SET icon should be off.

3.Press MODE button once. The SET icon will come on. The display now shows Option 19 setting.

4.Use up and down buttons to move between available Option 19 choices of 2 through 4. Factory default is 4.

5.Press MODE button again to return to Option 19. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

OPTION 21 - KEYPAD LOCKOUT

In OF (off) mode, the keypad is not locked out and has full functionality. In ON mode, the keypad is locked out and the lock icon on the display is illuminated. To unlock the keypad, the user must press and hold the up and down buttons simultaneously for approximately 5 seconds. The lock icon is turned off and the keypad will remain unlocked as long as the user presses a button at least every 30 seconds or for the entire duration of the installer test mode. If keypad remains idle for 30 seconds and the installer test mode is not in operation, the keypad will return to the locked state and the lock icon will illuminate on the screen.

4