SC-411RD-10 Installation and Operating Instructions Page 7 of 12
CP5094C 7/30/12
Option Set 1
S1 (CUTOUT Input), S2 (SIRCTRL Input),
S3 (LITCTRL Input) - These inputs are
normally activated by a 12V input ( ON).
Press the switch once u ntil it FLASHES to
change to ground activatio n. Press the
switch again for OFF to disable.
S4 (Timed Override) - While In Wail, Yelp or
Phaser mode, momentarily pressing the
Manual push button will override the W ail,
Yelp or Phase r tone. With this option ON
the unit automaticall y goes back to the
previous tone after 10 seconds.
S5 (Sweep/Intersection Function) - W hile in
Wail, Yelp, or Phaser mo de, momentarily
activating the siren control input will change
the unit into sweep and intersection mode.
S6 (Automa tic Siren Enable) The Auto-
matic Siren feature on the Lever switch
Position 3 may be enabled with this switch.
Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.
Option Set 2
S1 (Two-Tone Enable) - Two-Tone replaces
Phaser tone when turned ON.
S2 (Phaser/Two-Tone Disable) - Phaser
and Two-Tone are disabled when ON.
S3 (Short Manual Enable) - The Manual
siren tone will normally die out and stop
when Manual push-b utton is released.
Turning option ON forces the Manual siren
tone to stop immediately.
S4 (Horn Disable) - Horn tone is dis abled
when turned ON.
S5 (Leve r 2 Isolated) - Turn ON for L2
output only in Lever switch position 2.
S6 (Leve r 3 Isolated) - Turn ON for L3
output only in Lever switch position 3.
Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.
Option Set 3
S1 (Alert Enable) - Turn off to disable Alert
feature (reminder beep).
S2 (Lever/Siren Video) - VIDEO output is
normally on when the Lever switch and/or
Siren is ac tive. Press switch to disable.
(NOTE: this does not co ntrol the VIDEO
Output for S1 - S6. See S1 - S6 Operation)
Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.
Second Tone Control
Press S1, S2, S3 or S4 to select the second speaker tone when in the corresponding Function switch setting.
Press the OUT/DIM button momentarily to go back to beginning, or OUT/DIM for 3 seconds to save & exit.
NOTE: These option setting can be easily transferred to another vehicle. See PROGRAM TRANSFER.
Press Lever Switch = OFF Shows blinking
0↓
S1
On (Default) Cutout Input Active +
1↓ Flash Cutout Input Active -
2 Off Cutout Input Off
0↓
S2
On (Default) Siren Control Input Active +
1↓ Flash Siren Control Input Active -
2 Off Siren Control Input Off
0↓
S3
On (Default) Light Control Input Active +
1↓ Flash Light Control Input Active -
2 Off Light Control Input Off
0↓ S4 Off (Default) Timed Override Off
1 On Timed Override On
0↓ S5 Off (Default) Sweep/Intersection Off
1 On Sweep/Intersection On
0↓ S6 On (Default) Automatic Siren O n
1 Off Automatic Siren Off
Press Lever Switch = OFF Shows blinking
0↓ S1 Off (Default) Phaser
1 On Two-Tone Replace
0↓ S2 Off (Default) Phase r/Two-Tone Enable
1 On Phaser/Two-Tone Disable
0↓ S3 Off (Default) Normal Manual
1 On Short Manual
0↓ S4 Off (Default) Horn Enable
1 On Horn Disable
0↓ S5 Off (Default) Lever 2 Progressive
1 On Lever 2 Isolated
0↓ S6 Off (Default) Lever 3 Progressive
1 On Lever 3 Isolated
Press Lever Switch = OFF Shows blinking
0↓ S1 On (Default) Alert Enabled
1 Off Alert Disabled
0↓ S2 On (Default) Lever/Siren Video Enabled
1 Off Lever/Siren Video Disabled
Rotary
Position
Lever Switch = OFF Shows & blinking
S1 S2 S3 S4
WAIL 2
nd
= Wail 2
nd
= Yelp 2
nd
= Phaser 2
nd
= Two-Tone
YELP 2
nd
= Wail 2
nd
= Yelp 2
nd
= Phaser 2
nd
= Two-Tone
PHSR 2
nd
= Wail 2
nd
= Yelp 2
nd
= Phaser 2
nd
= Two-Tone