Casio 5213 Using the Stopwatch, Using the Countdown Timer, Using the Alarm, ASC, DSC, ASC, DSC, CLR, CLR, CLR, SPL, Stop, Stop, Stop, Note, Stop, Start, Split, Start

Operation Guide 5113 5213

	Manual Save 1	Manual Save 14	High Altitude (HI)
	Hour : Minutes
	1 second	1 second	1 second
Month	Record name
Day	Altitude	Altitude	High altitude
	Cumulative Descent (DSC)	Cumulative Ascent (ASC)	Low Altitude (LO)
	Cumulative recording	Cumulative recording
	start month and day	start month and day
			1 second
	1 second	1 second
	Cumulative descent	Cumulative ascent	Low altitude

E-64

3.After you are finished viewing data, use D to exit the Data Recall Mode.

•- . - - will be displayed if data has been deleted or if there is no corresponding data due to error, etc. In such cases, cumulative ascent (ASC) and cumulative descent (DSC) values will show zero.

•When the cumulative ascent (ASC) or cumulative descent (DSC) exceeds 99,995 meters (or 327,980 feet), the applicable value will restart from zero.

To delete a single altitude record

1.In the Data Recall Mode, use A and C to scroll through records until the one you want to delete is displayed.

2.Hold down E for about two seconds until each of the following steps occurs.

•Hold CLR appears on the digital display. ➝ CLR appears.

•This deletes the record you displayed in step 1.

•Release E after CLR appears on the digital display.

•Deleting a manual save record shifts all of the records following it up one position.

To delete all altitude records

In the Data Recall Mode, hold down E for about five seconds until each of the following steps occurs.

•Hold CLR appears on the digital display. ➝ CLR appears. ➝ Hold ALL appears. ➝ CLR ALL appears.

•This deletes all of the records currently in memory.

E-65

Using the Stopwatch

The stopwatch measures elapsed time, split times, and two finishes.

To measure two finishes

A	C	A	C	C
Start	Split	Stop	Split release	Reset

Seconds 1/100

Minutes second

To enter the Stopwatch Mode

Use D to select the Stopwatch Mode (ST) as shown on page E-16.

•About one second after ST appears on the digital display, the display will change to show the stopwatch time.

To perform an elapsed time operation

A	A	A	A	C
Start	Stop	(Restart)	(Stop)	Reset
To pause at a split time
A	C	C	A	C
Start	Split	Split release	Stop	Reset
	(SPL displayed)

First runner finishes.	Second runner	Display time of
Display time of first	finishes.	second runner
runner

Note

•The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59.99 seconds.

•Once started, stopwatch timing continues until you press C to stop it, even if you exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch limit defined above.

•Exiting the Stopwatch Mode while a split time is frozen on the digital display clears the split time and returns to elapsed time measurement.

E-66 E-67

Using the Countdown Timer

The countdown timer can be configured to start at a preset time, and sound an alarm when the end of the countdown is reached.

To perform a countdown timer operation

A	A	A	A	C
Start	Stop	(Restart)	(Stop)	Reset

Countdown time (Minutes, seconds)

To enter the Countdown Timer Mode

Use D to select the Countdown Timer Mode (TR) as shown on page E-16.

•About one second after TR appears on the digital display, the display will change to show the current countdown start time.

To specify the countdown start time

1.Enter the Countdown Timer Mode.

•If a countdown is in progress (indicated by the seconds counting down), press A to stop it and then press C to reset to the current countdown start time.

•If a countdown is paused, press C to reset to the current countdown start time.

2.Hold down E until each of the following steps occurs.

•Hold SET appears on the digital display. ➝ The current countdown start time flashes.

3.Use A (+) and C (–) to change the minute setting.

4.Press E to exit the setting screen.

•Before starting a countdown timer operation, check to make sure that a countdown operation is not in progress (indicated by the seconds counting down). If it is, press A to stop it and then C to reset to the countdown start time.

•An alarm sounds for five seconds when the end of the countdown is reached. This alarm will sound in all modes. The countdown time is reset to its starting value automatically when the alarm sounds.

To stop the alarm

Press any button.

E-68 E-69

Using the Alarm

To set an alarm time

Alarm time	Alarm
(Hour: Minutes)	number

You can set five independent daily alarms. When a daily alarm is turned on, an alarm tone will sound for about 10 seconds each day when the time in the Timekeeping Mode reaches the preset alarm time. This is true even if the watch is not in the Timekeeping Mode.

You can also turn on an Hourly Time Signal, which will cause the watch to beep twice every hour on the hour.

To enter the Alarm Mode

Use D to select the Alarm Mode (AL) as shown on page E-16.

•About one second after AL appears on the digital display, the display

will change to show an alarm number (−1 through −5) or the

indicator. The alarm number indicates an alarm screen.is shown when the Hourly Time Signal screen is on the digital display.

•When you enter the Alarm Mode, the data you were viewing when you last exited the mode appears first.

1. In the Alarm Mode, use A and C to scroll through the alarm (–1through –5) until the one whose time you want to set is displayed.

	−1	−2	−3
		−5	−4
Alarm ON/OFF 2. Hold down E until each of the following steps occurs.
indicator	• Hold SET appears on the digital display. ➝ The current setting

flashes.

• This is the setting screen.

3.Press D to move the flashing between the hour and minute settings.

4.While a setting is flashing, use A (+) and C (–) to change it.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator).

5.Press E to exit the setting screen.

E-70 E-71