CFM Corporation 2460, 2462, 2461 manual Stove Clearance, Chimney Connector Clearance

Dutchwest

Stove and Chimney Connector Clearance Charts

Model 2460 Small Convection, and Model 2461 Large Convection:

UNPROTECTED SURFACES

PROTECTED SURFACES

Corner

Corner

Parallel Installations

Installations

Parallel Installations

Installations

Stove Clearance

Side

Rear

Corner

Side

Rear

Corner

No heat shields

[A]

22” (560 mm)

[B]

24” (610 mm)

[C]

18” (460 mm)

[D] 12” (300 mm)

[E] 14” (360 mm)

[F] 10” (250 mm)

Rear exit, rear h.s.

[G]

22” (560 mm)

[H]

14” (360 mm)

N/A

[I]

12” (300 mm)

[J] 12” (300 mm)

N/A

Top exit1, rear h.s.

Single-wall connector

[K]

22” (560 mm)

[L]

24” (610 mm)

[M] 18” (460 mm)

[N]

12” (300 mm)

[O] 14” (360 mm)

[P] 10” (250 mm)

No connector h.s.

Top exit1,2 , rear h.s.

Single-wall connec-

[K]

22” (560 mm)

[L] 14” (360 mm)

[M] 15” (380 mm)

[N]

12”(300 mm)

[O] 12” (360 mm)

[P] 8” (200 mm)

tor with connector h.s.

Top exit1 , rear h.s.

Double-wall connector

[K]

22” (560 mm)

[L] 19” (480 mm)

[M] 15” (380 mm)

[N]

12” (300 mm

[O]

11” (280 mm)

[P] 8” (200 mm)

Chimney Connector Clearance:

Single-wall connector

19” 480 mm)

9” (230 mm)

No connector h.s

Single-wall2connector

9” (360 mm)

7” (180 mm)

With connector h.s.

Double-wall connector

14” (360 mm)

6” (150 mm)

Front Clearance to Combustibles:

48” (1220 mm) (All Installations)

Model 2462 Extra-Large Convection:

UNPROTECTED SURFACES

PROTECTED SURFACES

Corner

Corner

Parallel Installations

Installations

Parallel Installations

Installations

Stove Clearance

Side

Rear

Corner

Side

Rear

Corner

No heat shields

[A]

20” (510 mm)

[B]

23” (580 mm)

[C]

18” (460 mm)

[D]

18” (460 mm)

[E]

18” (460 mm)

[F]

17” (430 mm)

Rear exit, rear h.s.

[G]

20” (510 mm)

[H]

18” (460 mm)

N/A

[I]

18” (460 mm)

[J]

12” (300 mm)

N/A

Top exit1, rear h.s.

Single-wall connector

[K]

20” (510 mm)

[L]

23” (580 mm)

[M]

18” (460 mm)

[N]

18” (460 mm)

[O]

18” (460 mm)

[P]

17” (430 mm)

No connector h.s.

Top exit1,2 , rear h.s.

Single-wall connec-

[K]

20” (510 mm)

[L]

18” (460 mm)

[M]

17” (430 mm)

[N]

18” (460 mm)

[O]

12” (300 mm)

[P]

15” (380 mm)

tor with connector h.s.

Top exit1 , rear h.s.

Double-wall connector

[K]

20” (510 mm)

[L]

14” (360 mm)

[M]

16” (410 mm)

[N]

18” (460 mm)

[O]

12” (300 mm)

[P]

15” (380 mm)

Chimney Connector Clearance:

Single-wall connector

18” (460 mm)

13” (330 mm)

No connector h.s

Single-wall2connector

13” (330 mm)

7” (180 mm)3,4

With connector h.s.

Double-wall connector

8” (200 mm)

6” (150 mm)

Front Clearance to Combustibles:

48” (1220 mm) (All Installations)

1 Shielding for a top exit stove must include a shield insert to protect the area behind the flue collar.

2 Chimney connector heat shields must extend exactly 24” (610 mm) above the flue collar of the stove.

3 All installations venting straight up to a factory built chimney require a 24” (610 mm) diameter or square ceiling heat shield. The ceiling heat shield should be 24 gauge sheet metal or equivalent mounted on 1” (25 mm) non-combustible spacers 1” (25 mm) below ceiling.

4 Chimney connector heat shields must extend to within 1” (25 mm) or less of the ceiling heat shield for installations venting straight up to a factory-built chimney. In top exit installations using an elbow to vent to the rear, the chimney connector must be shielded over the entire vertical length.

5 If a single-wall oval-to-round adaptor is used, a shield must be used to protect combustibles to the rear of the adaptor.

7001135 13