Installation Step 6
Install the Multi-Function
Door Control Panel
•Strip 1/4" of insulation from one end of the bell wire; connect the wire to the two screw terminals on the back of the door control by color: white to 2 and white/red to 1.
•Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware. Fasten the
•Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short.
•Receiver terminal screws and the antenna are located on the right panel of the opener. Position the antenna wire as shown.
•Then connect the bell wire to the opener terminal screws: white to 2 and white/red to 1.
•Remember to affix the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction label in a prominent location on the inside of the garage door.
If the label adhesive will not adhere to your garage wall surface (or becomes loose with time) use tacks to secure the label alongside the door control.
Page 28 explains how to operate the opener using the lighted push button and the Lock & Light features available on the
Hardware Shown Actual Size
6AB x 1" Screw |
| Insulated |
Dry Wall Anchors | Staples |
WARNING
Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Install the door control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control transmitter(s).
A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see it clearly, and there are no obstructions to door travel.
Do NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.
See Safety Reversing Sensor Instructions beginning on page 17.
Outside Keylock Accessory Connections
To opener terminal screws: white to 2; white/red to 1
Door Control Panel
Terminal Screws
RED | WHITE |
1 | 2 |
|
Lock Button
LOCK
LIGHT | Light Button |
|
Door Control
Button
Door Control PanelRight Panel
of Opener
Opener
Terminal Screws
TO PROGRAM RECEIVER CODE |
| 1 |
| 2 |
| 3 |
|
|
| |
FOR EACH REMOTE CONTROL |
|
|
|
|
|
| ||||
1. Press and HOLD remote control |
|
|
|
|
|
|
|
|
|
|
transmitter push button. |
|
|
|
|
|
|
|
|
|
|
2. Press receiver code button. The opener |
|
|
|
|
|
|
|
|
|
|
light will flash once. |
|
|
|
|
|
|
|
|
|
|
3. Release transmnitter button. Opener |
|
|
|
|
|
|
|
|
|
|
has learned code. |
|
|
|
|
|
|
|
|
|
|
TO ERASE ALL RECEIVER CODES |
|
|
| 9 | 1 | 9 |
| 1 | ||
1. Press and HOLD receiver code button. |
|
|
|
|
|
|
|
|
|
|
Green indicator light alongside will turn |
|
|
| 7 | 3 | 7 | 3 |
| ||
ON. |
|
|
|
| 5 |
|
| 5 |
|
|
2. When light turns OFF (about 6 |
|
|
|
| KG |
|
| KG | ||
|
|
|
|
|
| |||||
seconds) ALL codes are erased from |
|
|
|
|
|
| ||||
opener memory. |
|
| This device complies | WARNING: To reduce the risk of severe injury | ||||||
|
|
| with FCC Rules Part | or death by entrapment, when adjusting either | ||||||
|
|
| 15. Operation of this | the force or limits of travel controls ensure that | ||||||
|
|
| the door reverses on a 1 inch object (or a 2 x 4 | |||||||
|
|
| device is subject to the | board laid flat). See instructions for proper | ||||||
|
|
| following conditions: | adjustment procedure. |
|
|
|
|
| |
|
|
| 1. This device may | AVERTISSEMENT: Pour réduire les risques de | ||||||
|
|
| not cause harmful | blessures mortelles par happement, après tout | ||||||
|
|
| interference. 2. This | réglage de la force de déclenchement ou des | ||||||
|
|
| device must accept | seuils de fin de course s'assurer que le sens de | ||||||
|
|
| any interference | la course s'inverse lorsque la porte entre en | ||||||
|
|
| that may be received, | contact avec un object de 13 mm (1 po) de | ||||||
|
|
| including interference | hauteur (ou un madrier de 2 x 4 de section, à | ||||||
|
|
| that may cause | plat) posé sur le sol. Effectuer les reglages | ||||||
|
|
| undesired operation. | selon les procédures décrites dans la notice. | ||||||
|
|
|
|
| PART NO: |
| Nº DE PIÈCE: | |||
|
|
|
|
| D.O.C. CERT. NO. | DATE: | ||||
|
|
|
|
| M.D.C. CERT. NO. | |||||
Antenna
14